Solef® 41308/0001 PVDF is specifically developed for coextrusion.

Solef® 41308/1001 PVDF is specifically developed for powder coating applications.

Solef® 42308/0001 PVDF is specifically developed for coextrusion.

Solef® 460S/461S PVDF homopolymer has high melt viscosity and is typically processed by extrusion.

Solef® 5000S is a crystalline high molecular weight powder form of polyvinylidene fluoride (PVDF) specifically designed for solvent-based non-architectural coatings. It forms mechanically strong and tough films that have a broad useful temperature range. These films are highly resistant to most environmental conditions including gamma radiation and are essentially transparent to ultraviolet radiation. The weathering characteristics of Solef® 5000S coatings lead to excellent performance for the long term. SAFETY Solef® 5000S is stable at temperatures up to 600°F (316°C). When it is subjected to temperatures above 600°F (316°C) for extended periods of time, hydrogen fluoride (HF) begins to evolve, and at temperatures above 700°F (371°C) HF evolution becomes rapid. Solef® 5000S exhibits excellent flame resistance; however, in case of fire, HF and traces of potentially toxic fluorocarbons can be formed. HF is corrosive, causes burns on contact, and has an American Conference Governmental Industrial Hygienists (ACGIH) Threshold Limit Value (TLV-TWA) of 3 ppm (2.5 mg/m³) (1984). Thermal decomposition of Solef® 5000S to HF can also occur in a bake oven in the event that temperatures are not controlled properly. In the event of fire, use NIOSH approved self-contained breathing apparatus and skin protection to protect against volatile decomposition products. Solef® 5000S can be disposed of in an approved landfill, but should not be incinerated unless permitted by applicable law and provision is made for absorption of HF.

ソレフ® 5120 PVDF は中粘度グレードで、リチウム電池での使用に最適な高い密着性を提供します。

ソレフ® 5130 PVDF は超高粘度グレードで、リチウム電池に最適な最高の密着性を提供します。

Solef® 5140 PVDF is an ultra high viscosity grade that gives superior adhesion and ultra high viscosity at reduced binder content, ideal for its use as binder in Lithium Ion Batteries.

ソレフ® 6008 PVDF ホモポリマーは低粘度の PVDF 樹脂で、一般に射出成形により加工されます。

ソレフ® 6010 PVDF ホモポリマーは中程度の粘度を有し、一般に押出成形により加工されます。

ソレフ® 6012 PVDF ホモポリマーは高粘度の PVDF 樹脂で、一般に押出成形または圧縮成形により加工されます。

ソレフ® 6020 PVDF ホモポリマーは、メンブレンおよびリチウム電池向けの非常に高い粘度を有します。パウダー形式だけで提供されます。

ソレフ® 60512/0550 およびソレフ® 60512/0150 は、耐摩耗性テープの押出成形用に PTFE とコンパウンディングされた PVDF グレードです。

ソレフ® 60512 PVDF コポリマーは、高い溶融粘度を持つ沖合配管用のグレードです。

Solef® 75040 PVDF copolymer is a ultra high molecular weight, chemically modified grade that combines excellent adhesion, good flexibility and easy solution process, which makes it ideal for usage in lithium batteries. Main features of Solef® 75040 PVDF are: - Good adhesion - Ultra high molecular weight - Good flexibility

Solef® 75130 PVDF copolymer is a ultra high molecular weight, chemically modified grade that combines excellent adhesion, good flexibility and easy solution process, which makes it ideal for usage in lithium batteries. Main features of Solef® 75130 PVDF are: - Good adhesion - Ultra high molecular weight - Soluble in acetone and ketones - Good flexibility

Carbon fibers reinforced - Injection

ソレフ® 9007 PVDF ホモポリマーは、粘度が低く、フィルムの押出成形や射出成形で使用されます。

Solef® 90615 PVDF copolymer has high viscosity of the melt and it is a grade for offshore piping.

Solef FPCH08/0001 is a low-viscosity PVDF resin typically processed by injection molding.

Solef FPCH09/0001 is a medium-low viscosity PVDF resin typically processed by injection molding.

Solef FPCH10/0001 is a medium-viscosity PVDF resin typically processed by extrusion.

Solef® Latex 2060 is an aqueous dispersion that contains approximately 21% by weight of a high molecular weight PVDF polymer (polyvinylidene fluoride) of high crystallinity. The dispersion is stable against coagulation by conventional means. Solef® Latex 2060 is useful for applications such as water-based impregnation of separators in Li-Ion batteries and energy storage devices. The main properties of Solef® Latex 2060 are: - Good adhesion to separator and to ceramics - Low swelling in hot electrolyte - Good wettability by electrolyte - Good flexibility - Good lamination to electrodes

Tecnoflon® PFR 06HC is a new chemical resistant perfluoroelastomer (FFKM). Tecnoflon® PFR 06HC offers the widest range of aggressive media sealing capabilities along with excellent compression set values. It is suitable for most applications in temperature ranging from -10°C to 230°C, offering outstanding resistance to aggressive media such as hot organic and inorganic acids, caustics, amines (especially hot amines, i.e. at temperature higher than 70°C), ketones, aldehydes, esters, ethers, alcohols, fuels, solvents, sour gases, hydrocarbons, steam, hot water, ethylene and propylene oxide and mixed process streams. Moreover it can cope with a wide range of potent active pharmaceutical ingredients (APIs) and aggressive cleaning agents, being especially suited to withstand steam-in-place (SIP) and clean-in-place (CIP) procedures. Moreover its structure was specifically designed to deliver enhanced extrusion resistance and rapid gas decompression (RGD or explosive decompression ED) resistance requested for many high pressure gas applications in the oil & gas industry. Its extreme cleanliness along with its broad chemical resistance make PFR 06HC the suitable sealing material for most wet semiconductor processes (wafer cleaning, polymer removal, wet etching, polishing), for photolithography developing and stripping and for general purpose fab equipments (pumps, scrubbers, filters, chemicals delivery systems). PFR 06HC can be combined with the cure system and other typical fluoroelastomer compounding ingredients; its mixing can be accomplished with two-roll mills or internal mixers. Finished goods may be produced by a variety of rubber processing methods. The primary use for PFR 06HC is the manufacturing of any kind of elastomeric sealing element such as O-rings, gaskets, valve bodies, butterfly valves, pump housings and stators, metal bonded parts, diaphragms, profiles, etc. These sealing elements can be used in mechanical seals, pumps, compressors, valves, reactors, mixers, sprayers, dispensers, quick connect couplings, controls, instrumentation, etc. in a wide range of industrial sectors. Tecnoflon® PFR 06HC is marketed in the form of raw polymer (1 kg box) in order to give the transformer the freedom and the opportunity to develop and fine-tune compounds and items best suited to the final application.

Tecnoflon® PFR 91 is a very high fluorine content, chemically resistant peroxide curable fluoroelastomer. It can withstand very aggressive conditions, such as almost all chemical species, including organic and inorganic acids, diluted alkalis, ketones, esters, alcohols, fuels and hot water. Tecnoflon® PFR 91 bridges the gap between traditional fluorocarbons and perfluoroelastomers. It offers much improved resistance to polar solvents (aldehydes, ketones, esters, ethers, lactones, etc.) and bases (like aqueous ammonia) than high fluorine content peroxide curable FKMs (like Tecnoflon® P 959). On the other hand, it shows enhanced cold flexibility when compared to FFKMs, as indicated by the TR10 value. Tecnoflon® PFR 91 represents the most cost effective sealing solution for solvent mixtures, as the ones to be found in the chemical and process, paint and lacquers industries as well as in biopharma laboratories and active pharmaceutical ingredient (API) manufacturing plants, for temperatures ranging from -20°C to 230°C. Tecnoflon® PFR 91 can be combined with the cure system and other typical fluoroelastomer compounding ingredients; its mixing can be accomplished with two-roll mills or internal mixers. Finished goods may be produced by a variety of rubber processing methods. The primary use for PFR 91 is the manufacturing of any kind of elastomeric sealing element such as O-rings, gaskets, valve bodies, butterfly valves, pump housings and stators, metal bonded parts, diaphragms, profiles, etc. These sealing elements can be used in mechanical seals, pumps, compressors, valves, reactors, mixers, sprayers, dispensers, quick connect couplings, controls, instrumentation, etc. in chemical and petrochemical industry, hydrocarbon processing, petroleum exploration and extraction, food processing, pharmaceutical and bio-analytical industry, aerospace and semiconductor manufacturing industries. Tecnoflon® PFR 91 is registered in the FDA Inventory of Effective Premarket Notifications for Food Contact Substances. It can be compounded so that the finished gaskets or seals can be used in food processing equipments (see "food processing compounds" section below). Tecnoflon® PFR 91 is marketed in the form of raw polymer (1 kg box) in order to give the transformer the freedom and the opportunity to develop and fine-tune compounds and items best suited to the final application.

Tecnoflon® PFR 94 is a chemical resistant perfluoroelastomer (FFKM). Tecnoflon® PFR 94 offers the widest range of aggressive media sealing capabilities along with excellent compression set values. Tecnoflon® PFR 94 is suitable for most applications in temperature ranging from -10 °C to 230 °C, offering outstanding resistance to aggressive media such as hot organic and inorganic acids, caustics, ketones, aldehydes, esters, ethers, alcohols, fuels, solvents, sour gases, hydrocarbons, steam, hot water, ethylene and propylene oxide and mixed process streams. Moreover it can cope with a wide range of potent active pharmaceutical ingredients (APIs) and aggressive cleaning agents, being especially suited to withstand steam-in-place (SIP) and clean-in-place (CIP) procedures. PFR 94 can be combined with the cure system and other typical fluoroelastomer compounding ingredients; its mixing can be accomplished with two-roll mills or internal mixers. Finished goods may be produced by a variety of rubber processing methods. The primary use for PFR 94 is the manufacturing of any kind of elastomeric sealing element such as O-rings, gaskets, valve bodies, butterfly valves, pump housings and stators, metal bonded parts, diaphragms, profiles, etc. These sealing elements can be used in mechanical seals, pumps, compressors, valves, reactors, mixers, sprayers, dispensers, quick connect couplings, controls, instrumentation, etc. in a wide range of industrial sectors, such as semiconductor manufacturing, chemical process industry, oil & gas, paint spray. Tecnoflon® PFR 94 is marketed in the form of raw polymer (1 kg and 5 kg boxes) in order to give the transformer the freedom and the opportunity to develop and fine-tune compounds and items best suited to the final application.

Tecnoflon® PFR 95 is a perfluoroelastomer (FFKM) offering wide operational range and superior compression set resistance, thanks to its unique peroxide curing system that does not need any coagent (TAIC or equivalent) for curing to be carried out. Thanks to its curing system, it can offer a very broad chemical resistance in a wide variety of media including acids, caustics, ketones, aldehydes, esters, ethers, methanol, solvents, sour gases, hydrocarbons, steam, hot water and mixed process streams along with excellent thermal resistance. Tecnoflon® PFR 95 is suitable for most applications in temperature ranging from -10 °C to 280 °C. Tecnoflon® PFR 95 can be combined with other typical fluoroelastomer compounding ingredients; its mixing can be accomplished with two-roll mills or internal mixers. Finished goods may be produced by a variety of rubber processing methods. The primary use for Tecnoflon® PFR 95 is the manufacturing of any kind of elastomeric sealing element such as O-rings, gaskets, valve bodies, butterfly valves, pump housings and stators, metal bonded parts, diaphragms, profiles, etc. These sealing elements can be used in mechanical seals, pumps, compressors, valves, reactors, mixers, sprayers, dispensers, quick connect couplings, controls, instrumentation, etc. in chemical and petrochemical industry, hydrocarbon processing, petroleum exploration and extraction, bio-analytical industry, aerospace and semiconductor manufacturing industries. Tecnoflon® PFR 95 is marketed in the form of raw polymer (1 kg and 5 kg boxes) in order to give the transformer the freedom and the opportunity to develop and fine-tune compounds and items best suited to produce high performance rubber articles such as O-rings, seals, diaphragms and other parts used in process industries.

Tecnoflon® PFR 95HT is a perfluoroelastomer (FFKM) offering a significantly wider operational range and superior compression set resistance than any other perfluoroelastomer, thanks to its unique peroxide curing system that does not need any coagent (TAIC or equivalent) for curing to be carried out. It can offer a very broad chemical resistance in a wide variety of media including acids, caustics, ketones, aldehydes, esters, ethers, methanol, solvents, sour gases, hydrocarbons, steam, hot water and mixed process streams along with excellent thermal resistance. Tecnoflon® PFR 95HT is suitable for most applications in temperature ranging from -10°C to 300°C. Tecnoflon® PFR 95HT can be combined with other typical fluoroelastomer compounding ingredients; its mixing can be accomplished with two-roll mills or internal mixers. Finished goods may be produced by a variety of rubber processing methods. The primary use for Tecnoflon® PFR 95HT is the manufacturing of any kind of elastomeric sealing element such as O-rings, gaskets, valve bodies, butterfly valves, pump housings and stators, metal bonded parts, diaphragms, profiles, etc. These sealing elements can be used in mechanical seals, pumps, compressors, valves, reactors, mixers, sprayers, dispensers, quick connectcouplings, controls, instrumentation, etc. in chemical and petrochemical industry, hydrocarbon processing, petroleum exploration and extraction, bio-analytical industry, aerospace and semiconductor manufacturing industries. Tecnoflon® PFR 95HT is marketed in the form of raw polymer (1 kg and 5 kg boxes) in order to give the transformer the freedom and the opportunity to develop and fine-tune compounds and items best suited to produce high performance rubber articles such as O-rings, seals, diaphragms and other parts used in process industries.

TECNOFLON® FOR 210 is a very low viscosity cure incorporated fluoroelastomer copolymer. Tecnoflon® FOR 210 is mainly intended for blending with other polymers of the Tecnoflon® family to achieve the desired viscosity. Tecnoflon® FOR 210 was developed with a new curing system that improves the physical properties of the finished product. Processing characteristics such as flow and scorch safety are also enhanced. Tecnoflon® FOR 210 is well suited for applications were superior flow, mold release and excellent compression set are required. Some of the basic properties of Tecnoflon® FOR 210 are: - Excellent scorch safety - Superior mold flow - Very good mold release - Lack of mold fouling - Low compression set - Good extrusion behaviour Tecnoflon® FOR 210 can be used for injection and transfer moulding of O-rings, gaskets, and seals. The product can be mixed using typical fluoroelastomers compounding ingredients and mixing can be accomplished with two-roll mills or internal mixers. The material can be extruded into hoses or profiles and can be calendered to make sheet stocks or belting. Finished goods can be produced by a variety of rubber processing methods.

TECNOFLON® FOR 3390 is a medium viscosity cure incorporated fluoroelastomer terpolymer (FKM) with high fluorine content (70 % wt). Tecnoflon® FOR 3390 is designed for applications requiring outstanding fuel and chemical resistance. Some of the basic properties of Tecnoflon® FOR 3390 are: - Good scorch safety - Reduced mold fouling - Excellent mold release - Excellent resistance to fuels - Very good heat resistance - Very good compression set TECNOFLON® FOR 3390 can be used for compression, injection and transfer moulding of shaft seals, valve stem seals, gaskets or any item requiring excellent chemical resistance. This material can be combined with the cure system and other typical fluoroelastomers compounding ingredients. Mixing can be accomplished with two-roll mills or internal mixers. TECNOFLON® FOR 3390 can be extruded into hoses or profiles and can be calendered to make sheet stocks or belting. Finished goods can be produced by a variety of rubber processing methods.

TECNOFLON® FOR 421/U is a low viscosity cure incorporated fluoroelastomer copolymer. This grade is well suited for applications where superior flow, mold release, and excellent compression set are required. Tecnoflon® FOR 421/U can be compounded to meet the major fluoroelastomer specifications. Some of the basic properties of Tecnoflon® FOR 421/U are: - Very fast cure rate - Very good scorch safety - Superior mold flow - Excellent mold release - Lack of mold fouling - Excellent compression set - Good extrusion TECNOFLON® FOR 421/U can be used for injection and transfer moulding of O-rings, gaskets, and seals. The product can be mixed using typical fluoroelastomers compounding ingredients and mixing can be accomplished with two-roll mills or internal mixers. The material can be extruded into hoses or profiles and can be calendered to make sheet stocks or belting. Finished goods can be produced by a variety of rubber processing methods.

TECNOFLON® FOR 5312K is a medium-low viscosity cure incorporated fluoroelastomer copolymer. This grade contains proprietary cure system and special processing aid providing superior processability. Tecnoflon® FOR 5312K is designed to improve bonding in any application requiring adhesion to metal. In shaft seals or valve stem seals production, Tecnoflon® FOR 5312K greatly reduces the reject rate due to adhesion and molding problems. Some of the basic properties of Tecnoflon® FOR 5312K are: - Superior bonding to metal - Very good scorch safety - Outstanding processability - Lack of mold fouling - Excellent hot tear resistance - Excellent mold release TECNOFLON® FOR 5312K can be used for injection and transfer moulding of gaskets and seals. The product can be mixed using typical fluoroelastomers compounding ingredients and mixing can be accomplished with two-roll mills or internal mixers. The material can be extruded into hoses or profiles and can be calendered to make sheet stocks or belting. Finished goods can be produced by a variety of rubber processing methods.

TECNOFLON® FOR 532 is a medium viscosity cure incorporated fluoroelastomer copolymer. This grade is well suited for applications where excellent compression set and superior mold release, are required. It can be compounded to meet MIL-R83428B and other major fluoroelastomer specifications. Some of the basic properties of Tecnoflon® FOR 532 are: - Very fast cure rate - Excellent scorch safety - Good mold flow - Superior mold release - Lack of mold fouling - Very low compression set TECNOFLON® FOR 532 can be used for compression and transfer moulding of O-rings, gaskets, and seals. The product can be mixed using typical fluoroelastomers compounding ingredients and mixing can be accomplished with two-roll mills or internal mixers. The material can be extruded into hoses or profiles and can be calendered to make sheet stocks or belting. Finished goods can be produced by a variety of rubber processing methods.

TECNOFLON® FOR 5351/U is a low viscosity cure incorporated fluoroelastomer copolymer. This grade has excellent flow and good compression set. Tecnoflon® FOR 5351/U can be used for molded items with complicated shapes which require a very good hot tear resistance for part removal. Some of the basic properties of Tecnoflon® FOR 5351/U are: - Very fast cure rate - Very good scorch safety - Superior mold flow - Excellent mold release - Lack of mold fouling - Low compression set - High elongation - Excellent hot tear strength TECNOFLON® FOR 5351/U can be used for injection and transfer moulding of gaskets and seals. The product can be mixed using typical fluoroelastomers compounding ingredients and mixing can be accomplished with two-roll mills or internal mixers. The material can be extruded into hoses or profiles and can be calendered to make sheet stocks or belting. Finished goods can be produced by a variety of rubber processing methods.

TECNOFLON® FOR 5361 is a low viscosity cure incorporated fluoroelastomer terpolymer designed to provide improved low temperature characteristics. Tecnoflon® FOR 5361 exhibits the same excellent heat and chemical resistance expected from Tecnoflon® copolymers. Some of the basic properties of Tecnoflon® FOR 5361 are: - Improved low temperature performance - Good chemical resistance - Good heat resistance - Very low compression set - Excellent mould release - Lack of mould fouling - Superior mould flow Tecnoflon® FOR 5361 can be used for injection, compression and transfer molding of O-rings, diaphragms, gaskets, seals, moulded shapes or other items requiring improved low temperature performance. Tecnoflon® FOR 5361 can be combined with the cure system and other typical fluoroelastomer compounding ingredients. Mixing can be accomplished with two-roll mills or internal mixers. This material can be extruded into hoses or profiles and can be calendered to make sheet stocks or belting. Finished goods can be produced by a variety of rubber processing methods.

TECNOFLON® FOR 537 is a low viscosity cure incorporated fluoroelastomer copolymer. This grade is especially suited for injection molding of O-rings and sealing components which must meet demanding specifications. Tecnoflon® FOR 537 contains a proprietary cure system and a special processing aid providing superior processability for fast cycles and scorch safety. It has been particularly designed to offer improved characteristics such as flow, mold release, scorch safety and faster cycles at higher molding temperatures. Some of the basic properties of Tecnoflon® FOR 537 are: - Best for high duro and non black compounds - O-ring curative level - Low viscosity - Improved scorch safety - Easiest mold release, no mold fouling TECNOFLON® FOR 537 can be used for injection and transfer moulding of O-rings, gaskets, and seals. The product can be mixed using typical fluoroelastomers compounding ingredients and mixing can be accomplished with two-roll mills or internal mixers. The material can be extruded into hoses or profiles and can be calendered to make sheet stocks or belting. Finished goods can be produced by a variety of rubber processing methods.

TECNOFLON® FOR 5381 is a low viscosity cure incorporated fluoroelastomer terpolymer (FKM) with 68.5% fluorine content. Tecnoflon® FOR 5381 is well suited for all applications requiring better chemical resistance and/or long term heat resistance compared to fluoroelastomer copolymers. Tecnoflon® FOR 5381 contains proprietary cure system and special process aid providing superior processability for fast cycles and scorch safety. Some of the basic properties of TECNOFLON® FOR 5381 are: - Very good processability - Excellent chemical resistance - Low compression set - Good heat resistance Tecnoflon® FOR 5381 can be used for compression, injection and transfer moulding of shaft seals, valve stem seals, gaskets or any item requiring excellent chemical resistance. This material can be combined with the cure system and other typical fluoroelastomer compounding ingredients. Mixing can be accomplished with two-roll mills or internal mixers. Tecnoflon® FOR 5381 can be extruded into hoses or profiles and can be calendered to make sheet stocks or belting. Finished goods can be produced by a variety of rubber processing methods.

TECNOFLON® FOR 60K is a medium-low viscosity cure incorporated fluoroelastomers copolymer. This grade is designed to improve bonding in any application requiring adhesion to metal. In shaft seals or valve stem seals production, Tecnoflon® FOR 60K greatly reduces the reject rate due to adhesion problems. Some of the basic properties of Tecnoflon® FOR 60K are: - Superior bonding to metal - Very good scorch safety - Superior mold flow - Lack of mold fouling - Excellent hot tear resistance - Excellent mold release Tecnoflon® FOR 60K can be used for injection, compression, and transfer moulding of gaskets and seals. The product can be mixed using typical fluoroelastomers compounding ingredients and mixing can be accomplished with two-roll mills or internal mixers. The material can be extruded into hoses or profiles and can be calendered to make sheet stocks or belting. Finished goods can be produced by a variety of rubber processing methods.

TECNOFLON® FOR 7352 is a medium-low viscosity cure incorporated fluoroelastomer copolymer. TECNOFLON® FOR 7352 is well suited for applications where excellent compression set and superior mold release are required. Some of the basic properties of Tecnoflon® FOR 7352 are: - Very good scorch safety - Good mold flow - Excellent mold release - Lack of mold fouling TECNOFLON® FOR 7352 can be used for compression and transfer moulding of O-rings, gaskets, and seals. The product can be mixed using typical fluoroelastomers compounding ingredients and mixing can be accomplished with two-roll mills or internal mixers. The material can be extruded into hoses or profiles and can be calendered to make sheet stocks or belting. Finished goods can be produced by a variety of rubber processing methods.

TECNOFLON® FOR 7353 is a medium-low viscosity cure incorporated fluoroelastomer copolymer. Tecnoflon® FOR 7353 is well suited for applications where excellent compression set and superior mold release are required. Some of the properties of Tecnoflon® FOR 7353 are: - Very good scorch safety - Good mold flow - Excellent mold release - Lack of mold fouling - FDA compliant TECNOFLON® FOR 7353 can be used for compression and transfer moulding of O-rings, gaskets and seals. The product can be mixed using typical fluoroelastomers compounding ingredients and mixing can be accomplished with two-roll mills or internal mixers. The material can be extruded into hoses or profiles and can be calendered to make sheet stocks or belting. Finished goods can be produced by a variety of rubber processing methods. Some FDA compliant compounds are reported in the table n° 2.