Rilsan® 8020 resin is a translucent flexible copolyamide based on renewable resources and without plasticizer. This grade is specially designed for medical uses.

Rilsan® BECNO TL resin is a polyamide produced from a renewable source. This natural grade is designed for cable coating. 11 The percentage of renewable carbon according to ASTM D 6866 (calculated) is >98%.

Rilsan® BECV BLUE T8L resin is a polyamide 11 produced from a renewable source. This blue coloured grade is designed for cable coating but is also suitable for extrusion. The percentage of renewable carbon according to ASTM D 6866 (calculated) is >95%.

Rilsan® BES BLACK PR resin is a polyamide 11 produced from a renewable source. This black grade is plasticized and designed for extrusion.

Rilsan® BESHV BLK T is an ultra high viscosity Polyamide 11 grade specifically designed to be extruded into large diameter thick wall pipe. This grade has been specifically engineered to achieve an outstanding balance of properties for Oil & Gas piping applications. It offers a cost effective system for non-metallic corrosion free fluid transfer in critical Oil and Gas industry applications. Rilsan® Polyamide 11 is a thermoplastic material permitted by the US Department of Transportation (DOT) under the Code of Federal Regulations (CFR) Title 49, Part 192, for gas distribution piping to be installed and operated at pressures up to and including 250 psi in a design factor of 0.40. The percentage of renewable carbon according to ASTM D 6866 (calculated) is >95%.

Rilsan® BESN BLACK P123 TL resin is a flexible polyamide 11 produced from a renewable source. This black grade is designed for extrusion typically for cooling application and for Adblue circuits (SCR). The pourcentage of renewable carbon (calculated) is 67% (Value obtained from a calculation based on the composition of the raw material that are used to manufacture the product. Arkema has not made a specific measure on the product).

Rilsan® BESN BLACK P126 T6L resin is a flexible polyamide 11 produced from a renewable source. This grade is designed for tube extrusion and has a high thermo-oxidative resistance. The percentage of renewable carbon according to ASTM D 6866 (calculated) is >75%. Note that this document is a temporary technical data sheet.

Rilsan® BESN BLACK P20 TL resin is a polyamide 11 produced from a renewable source. This black grade is plasticized and designed for extrusion. The percentage of renewable carbon according to ASTM D 6866 (calculated) is >92%.

Rilsan® BESN BLACK P210 TL resin is a polyamide 11 produced from a renewable source. This black grade is plasticized and designed for extrusion. Rilsan® BESN BLACK P210 TL resin falls into the PA11-PHLY category according to DIN 73378 and fulfills all specifications according to DIN 74324, ISO 7628, NFR 12632, and SAEJ844. The percentage of renewable carbon according to ASTM D 6866 (calculated) is >88%.

Rilsan® PA 11 G BESN BLACK P212 CTL resin is a polyamide 11 produced from a renewable source. This black grade is specially designed for conductive multi-layers fuel line applications. The percentage of renewable carbon according to ASTM D 6866 (calculated) is >55%.

Rilsan® BESN BLACK P40 TL resin is a polyamide 11 produced from a renewable source. This black grade is plasticized and designed for extrusion. The percentage of renewable carbon according to ASTM D 6866 (calculated) is >88%.

Rilsan® BESN BLACK P40 TL01 resin is a polyamide 11 produced from a renewable source. This black grade is plasticized and designed for extrusion. The percentage of renewable carbon according to ASTM D 6866 (calculated) is >89%.

Rilsan® BESN BLACK TL resin is a polyamide 11 produced from a renewable source. This black grade is designed for extrusion. The percentage of renewable carbon according to ASTM D 6866 (calculated) is >97%.

Rilsan® BESN G9 TL resin is a polyamide 11 produced from a renewable source. This black grade with improved friction properties is designed for extrusion. The percentage of renewable carbon according to ASTM D 6866 (calculated) is >85%.

Rilsan® BESN YELLOW 41 TL resin is a polyamide 11 produced from a renewable source. This yellow colored grade is designed for extrusion. The percentage of renewable carbon according to ASTM D 6866 (calculated) is >97%.

Rilsan® BESNO 23 TL4 CC resin is a polyamide 11 produced from a renewable source. This grade with good translucence properties is designed for extrusion. The percentage of renewable carbon according to ASTM D 6866 (calculated) is >90%.

Rilsan® BESNO MED resin is a polyamide 11 produced from a renewable source. This grade dedicated to extrusion offers the highest quality and it is specifically designed to meet the stringent requirements of the medical applications such as minimally invasive devices. Upon request, letters regarding USP Class VI compliance can be provided. The percentage of renewable carbon according to ASTM D 6866 (calculated) is 100%.

Rilsan® BESNO P20 TL resin is a polyamide 11 produced from a renewable source. This natural grade is plasticized and designed for extrusion. The percentage of renewable carbon according to ASTM D 6866 (calculated) is >93%.

Rilsan® BESNO P20 TLO resin is a polyamide 11 produced from a renewable source. This natural grade is plasticized and designed for extrusion. This grade contains a low amount of oligomers. The percentage of renewable carbon according to ASTM D 6866 (calculated) is >93%.

Rilsan® BESNO P210 TL resin is a polyamide 11 produced from a renewable source. This natural grade is plasticized and designed for extrusion. Rilsan® BESNO P210 TL resin falls into the PA11-PHLY category according to DIN 73378 and fulfils all specifications according to DIN 74324, ISO 7628, NFR 12632 and SAE J844 The percentage of renewable carbon according to ASTM D 6866 (calculated) is >89%.

Rilsan® BESNO P40 TL resin is a polyamide 11 produced from a renewable source. This natural grade is plasticized and designed for extrusion. The percentage of renewable carbon according to ASTM D 6866 (calculated) is >89%.

Rilsan® BESNO P40 TLO resin is a polyamide 11 produced from a renewable source. This natural grade is plasticized and designed for extrusion. This grade contains a low amount of oligomers. The percentage of renewable carbon according to ASTM D 6866 (calculated) is >85%.

plasticized and designed for extrusion of large pipe as used in Oil and Gaz applications. This grade does not contain any lubricant. The percentage of renewable carbon according to ASTM D 6866 (calculated) is >89%.

Rilsan® BESNO P40 TLX resin is a polyamide 11 produced from a renewable source. This natural grade is plasticized and designed for extrusion of large pipe as used in Oil and Gaz applications. The percentage of renewable carbon according to ASTM D 6866 (calculated) is >89%.

Rilsan® BESNO P40 W6 TL resin is a polyamide 11 produced from a renewable source. This grade is plasticized and designed for extrusion. This grade is classified as Halogen Free Flame Retardant (HFFR). The percentage of renewable carbon according to ASTM D 6866 (calculated) is >79%.

Rilsan® BESNO P400 TL NL resin is a polyamide 11 produced from a renewable source. This natural grade is plasticized and designed for extrusion.

Rilsan® BESNO TL NB resin is a polyamide 11 produced from a renewable source. This natural grade is designed for extrusion and it does not contain any optical brightener. The percentage of renewable carbon according to ASTM D 6866 (calculated) is >98%.

Rilsan® BESNO TL resin is a polyamide 11 produced from a renewable source. This natural grade is designed for extrusion. The percentage of renewable carbon is 96% (calculated value, based on ASTM D6866).

Rilsan® BESVO A FDA resin is a polyamide 11 produced from a renewable source. This natural grade, dedicated to extrusion, contains a negligible amount of oligomers and is specially designed for food contact applications. The percentage of renewable carbon according to ASTM D 6866 (calculated) is 100%.

Rilsan® BESVO A MED resin is a polyamide 11 produced from a renewable source. This natural grade, dedicated to extrusion, contains a negligible amount of oligomers. Rilsan® BESVO A MED resin offers the highest quality and it is specially designed to meet the stringent requirements of the medical applications such as minimally invasive devices. Upon request letters regarding USP Class VI compliance can be provided. The percentage of renewable carbon according to ASTM D 6866 (calculated) is 100%.

Rilsan® BMN BLACK TLD resin is a polyamide 11 produced from a renewable source. This black grade is designed for injection molding. The percentage of renewable carbon according to ASTM D 6866 (calculated) is >94%.

Rilsan® BMN G8 TLDA resin is a polyamide 11 produced from a renewable source. This grade is designed for injection molding with improved friction properties and approuved for drinking water contact : WRAS (UK). The percentage of renewable carbon according to ASTM D 6866 (calculated) is >94%.

Rilsan® BMN Y TLD resin is a polyamide 11 produced from a renewable source. This grade is "self-lubricated" and designed for injection molding. The percentage of renewable carbon according to ASTM D 6866 (calculated) is >98%.

Rilsan® BMNO MED resin is a polyamide 11 produced from a renewable source. This natural grade dedicated to injection offers the highest quality and it is specially designed to meet the stringent requirements of the medical applications such as minimally invasive devices. Upon request letters regarding USP Class VI compliance can be provided. The percentage of renewable carbon according to ASTM D 6866 (calculated) is 100%.

Rilsan® BMNO P20 TLD resin is a polyamide 11 produced from a renewable source. This natural grade is plasticized and designed for injection molding. The percentage of renewable carbon according to ASTM D 6866 (calculated) is >92%.

Rilsan® BMNO P40 TLD resin is a polyamide 11 produced from a renewable source. This natural grade is plasticized and designed for injection molding. The percentage of renewable carbon according to ASTM D 6866 (calculated) is >88%.

Rilsan® BMNO SG FILAGE resin is a polyamide 11 produced from a renewable source. This natural grade is particularly suitable for textile applications. The percentage of renewable carbon measured according to ASTM D6866 is 98%.

Rilsan® BMNO TLD resin is a polyamide 11 produced from a renewable source. This natural grade is designed for injection molding. The percentage of renewable carbon according to ASTM D 6866 (calculated) is >97%.

Rilsan® BMNO resin is a polyamide 11 produced from a renewable source. This natural grade contains no additive and is specially designed for food contact application. The percentage of renewable carbon measured according to ASTM D6866 is 98%.

Rilsan® BMV WHITE 5 P20 D resin is a polyamide 11 produced from a renewable source. This white coloured grade is platicized and designed for injection molding. The percentage of renewable carbon according to ASTM D 6866 (calculated) is >89%.