| Product Description | |
|
4LOY 10E17300 is a MFI 14 to 16 85% PC / 15% ABS PC/ABS
|
|
| General | |
|
Material Status
|
|
|
Availability
|
|
|
Processing Method
|
|
| Physical |
Nominal Value
|
Unit
|
Test Method
|
|
Density
|
|
g/cm³
|
ISO 1183 |
|
Molding Shrinkage -
Flow
|
|
%
|
|
|
Water Absorption 2 (Equilibrium, 73°F, 50% RH)
|
|
%
|
ISO 62 |
| Mechanical |
Nominal Value
|
Unit
|
Test Method
|
|
Tensile Modulus (73°F)
|
|
psi
|
ISO 527-2/5 |
|
Tensile Stress
|
ISO 527-2/5 | ||
|
Yield, 73°F
|
|
psi
|
|
|
Break, 73°F
|
|
psi
|
|
|
Tensile Strain
|
ISO 527-2/5 | ||
|
Yield, 73°F
|
|
%
|
|
|
Break, 73°F
|
|
%
|
|
| Impact |
Nominal Value
|
Unit
|
Test Method
|
|
Notched Izod Impact Strength
|
ISO 180/1A | ||
|
-22°F
|
|
ft·lb/in²
|
|
|
73°F
|
|
ft·lb/in²
|
|
| Thermal |
Nominal Value
|
Unit
|
Test Method
|
|
Heat Deflection Temperature
|
|||
|
66 psi, Unannealed
|
|
°F
|
ISO 75-2/B |
|
264 psi, Unannealed
|
|
°F
|
ISO 75-2/A |
|
Vicat Softening Temperature
|
|
°F
|
ISO 306/B |
| Flammability |
Nominal Value
|
Unit
|
Test Method
|
|
Flame Rating (0.06 in)
|
|
|
UL 94 |
|
Glow Wire Ignition Temperature (0.08 in)
|
|
°F
|
IEC 60695-2-13 |
| Available Documents | |||
|
Processing (English)
Technical Datasheet (English) |
|||
| Injection |
Nominal Value
|
Unit
|
|
|
Drying Temperature
|
|
°F
|
|
|
Drying Time
|
|
hr
|
|
|
Suggested Max Moisture
|
|
%
|
|
|
Processing (Melt) Temp
|
|
°F
|
|
|
Mold Temperature
|
|
°F
|
|
|
Injection Rate
|
|
|
|
|
Holding Pressure
|
|
psi
|
|
|
Screw Speed
|
|
rpm
|
|
| Injection Notes | |||
|
Feed Throat Temperature: 60 - 80 °C
Back Pressure: Low |
|||
| Notes |
| 1Typical properties: these are not to be construed as specifications. |
| 224 Hrs |
|
UL and the UL logo are trademarks of UL LLC © 2021. All Rights Reserved.
The information presented here was acquired by UL from the producer of the product or material or original information provider. However, UL assumes no responsibility or liability for the accuracy of the information contained on this website and strongly encourages that upon final product or material selection information is validated with the manufacturer. This website provides links to other websites owned by third parties. The content of such third party sites is not within our control, and we cannot and will not take responsibility for the information or content. |