ABSplus™ P430 Datasheet

Acrylonitrile Butadiene Styrene

Supplied by Stratasys

Create your free Prospector account to view this complete product datasheet. A free account includes access to hundreds of thousands of detailed technical datasheets. Create Your Free Account
Product Description
Production-Grade Thermoplastic for Dimension 3D Printers

ABSplus is a true production-grade thermoplastic that is durable enough to perform virtually the same as production parts. When combined with Dimension 3D Printers, ABSplus is the ideal solution to printing 3D models in an office environment.
General  
Material Status 
  • Commercial: Active
Availability 
  • Africa & Middle East
  • Asia Pacific
  • Europe
  • Latin America
  • North America
Features 
  • Durable
Uses 
  • Additive Manufacturing (3D Printing)
  • Modeling Material
 
UL File Number 
  • E345258
Appearance 
  • Black
  • Blue
  • Dark Green
  • Dark Grey
  • Ivory
  • Orange
  • Red
  • White
  • Yellow
Processing Method 
  • 3D Printing, Fused Filament Fabrication (FFF)
Physical
Nominal Value
Unit
Test Method
Density / Specific Gravity
 
ASTM D792
Thickness - Layer Capability
mil
 
Mechanical
Nominal Value
Unit
Test Method
Tensile Modulus 2 (0.125 in)
psi
ASTM D638
Tensile Strength 2 (0.125 in)
psi
ASTM D638
Tensile Elongation 2 (Break, 0.125 in)
%
ASTM D638
Flexural Modulus 3
psi
ASTM D790
Flexural Strength 3
psi
ASTM D790
Flexural Delamination
psi
ASTM D790
Impact
Nominal Value
Unit
Test Method
Notched Izod Impact (73°F)
ft·lb/in
ASTM D256A
Thermal
Nominal Value
Unit
Test Method
Deflection Temperature Under Load
    ASTM D648
66 psi, Unannealed
°F
 
264 psi, Unannealed
°F
 
Glass Transition Temperature
°F
DMA
CLTE - Flow
in/in/°F
ASTM E831
Electrical
Nominal Value
Unit
Test Method
Dielectric Strength 4
     
Method A (Short-Time)
V/mil
ASTM D149
--
V/mil
IEC 60112
Dielectric Constant 4
 
ASTM D150
Dissipation Factor 4
 
ASTM D150
Volume Resistance 4
ohms
ASTM D257
Flammability
Nominal Value
Unit
Test Method
Flame Rating (0.09 in)
 
UL 94
Uses
Uses may also be described by the following terms: Additive Manufacturing, 3D Printing,3-D Printing.
Available Documents
Technical Datasheet (English)
Notes
1Typical properties: these are not to be construed as specifications.
2Type I, 0.20 in/min
3Method I (3 point load), 0.050 in/min
4All Electrical Property values were generated from the average of test plaques built with default part density (sparse). Test plaques were 4.0 x 4.0 x 0.1 inches (102 x 102 x 2.5 mm) and were built both in the flat and vertical orientation. The range of values is mostly the result of the difference in properties of test plaques built in the flat vs. vertical orientation.
 
UL and the UL logo are trademarks of UL LLC © 2020. All Rights Reserved.
The information presented here was acquired by UL from the producer of the product or material or original information provider. However, UL assumes no responsibility or liability for the accuracy of the information contained on this website and strongly encourages that upon final product or material selection information is validated with the manufacturer. This website provides links to other websites owned by third parties. The content of such third party sites is not within our control, and we cannot and will not take responsibility for the information or content.