ULTEM™ Resin 6202 - Americas Datasheet

Polyether Imide

Supplied by SABIC

Create your free Prospector account to view this complete product datasheet. A free account includes access to hundreds of thousands of detailed technical datasheets. Create Your Free Account
Product Description
12% Silica filled, standard flow Polyetherimide Copolymer (Tg 235C). ECO Conforming, UL94 VO Listing.
General  
Material Status 
  • Commercial: Active
Availability 
  • Latin America
  • North America
 
Uses 
  • Electrical/Electronic Applications
  • Electronic Displays
 
Also Available In 
  • Europe
Physical
Nominal Value
Unit
Test Method
Density / Specific Gravity
 
ASTM D792
Melt Mass-Flow Rate (MFR) (367°C/6.6 kg)
g/10 min
ASTM D1238
Molding Shrinkage - Flow (0.126 in)
%
Internal Method
Water Absorption (24 hr)
%
ASTM D570
Mechanical
Nominal Value
Unit
Test Method
Tensile Strength 2
    ASTM D638
Yield
psi
 
Break
psi
 
Tensile Elongation 2 (Break)
%
ASTM D638
Flexural Modulus 3 (3.94 in Span)
psi
ASTM D790
Flexural Strength 3
    ASTM D790
Yield, 3.94 in Span
psi
 
Break, 3.94 in Span
psi
 
Taber Abrasion Resistance (1000 Cycles, 1000 g, CS-17 Wheel)
mg
ASTM D1044
Impact
Nominal Value
Unit
Test Method
Notched Izod Impact (73°F)
ft·lb/in
ASTM D256
Unnotched Izod Impact (73°F)
ft·lb/in
ASTM D4812
Hardness
Nominal Value
Unit
Test Method
Rockwell Hardness (M-Scale)
 
ASTM D785
Thermal
Nominal Value
Unit
Test Method
Deflection Temperature Under Load (264 psi, Unannealed, 0.252 in)
°F
ASTM D648
Vicat Softening Temperature
°F
ASTM D1525 4
CLTE
    ASTM E831
Flow : -4 to 302°F
in/in/°F
 
Transverse : -4 to 302°F
in/in/°F
 
RTI Elec 5
°F
UL 746
RTI Imp 5
°F
UL 746
RTI Str 5
°F
UL 746
Electrical
Nominal Value
Unit
Test Method
Volume Resistivity
ohms·cm
ASTM D257
Dielectric Strength (0.0630 in, in Oil)
V/mil
ASTM D149
Dielectric Constant (1 kHz)
 
ASTM D150
Dissipation Factor (1 kHz)
 
ASTM D150
Flammability
Nominal Value
Unit
Test Method
Flame Rating (0.06 in)
 
UL 94
Oxygen Index
%
ASTM D2863
Related Terminology
This supplier and product may also be known by these terms: GE Plastics, LNP Engineering Plastics, GE Polymerland, SABIC Innovative Plastics, SABIC Americas, Saudi Basic Industries Corporation
Uses
Uses may also be described by the following terms: Electrical Applications, Electronic Applications, Electrical/Electronic Applications, Electrical Sector, Electronic Displays.
Injection
Nominal Value
Unit
 
Drying Temperature
°F
 
Drying Time
hr
 
Suggested Max Moisture
%
 
Suggested Shot Size
%
 
Rear Temperature
°F
 
Middle Temperature
°F
 
Front Temperature
°F
 
Nozzle Temperature
°F
 
Processing (Melt) Temp
°F
 
Mold Temperature
°F
 
Back Pressure
psi
 
Screw Speed
rpm
 
Vent Depth
in
 
Injection Notes
Injection Molding Parameters
  • Drying Time (Cumulative): 24 hrs
Notes
1Typical properties: these are not to be construed as specifications.
2Type I, 0.20 in/min
30.10 in/min
4Rate A (50°C/h), Loading 2 (50 N)
5UL Ratings shown on the technical datasheet might not cover the full range of thicknesses and colors. For details, please see the UL Yellow Card.
 
UL and the UL logo are trademarks of UL LLC © 2020. All Rights Reserved.
The information presented here was acquired by UL from the producer of the product or material or original information provider. However, UL assumes no responsibility or liability for the accuracy of the information contained on this website and strongly encourages that upon final product or material selection information is validated with the manufacturer. This website provides links to other websites owned by third parties. The content of such third party sites is not within our control, and we cannot and will not take responsibility for the information or content.