Addisil™ 2060 E Datasheet

Rubber

Supplied by Momentive Performance Materials Inc.

Create your free Prospector account to view this complete product datasheet. A free account includes access to hundreds of thousands of detailed technical datasheets. Create Your Free Account
Product Description
The Addisil 20X0 E series is a two-component heat curable rubber for making elastomers (HCE) with a hardness range between 50 and 80 Shore A for industrial applications. This series is based on a platinum cure system, which is particularly suitable for high value extrusion applications where regulatory compliance, transparency, mechanical performance and/or productivity are important. Application examples are oven door profiles and tubing for food applications.

Key Features and Benefits
  • Good transparency, no yellowing
  • Good mechanical performance
  • Dry, non-stick surface
  • Odourless during processing and in its application
  • Fast curing
  • Long shelf life of 6 months for the single components if stored appropriatelyM
  • Very long pot life of 2 to 4 weeks for the mixed components
  • Suitable for compliance with the food contact regulations FDA 21 CFR 177.2600 and the BfR section XV recommendations
  • KTW: German Water Regulation. A representative sample has passed the test for tubes, fittings, seals and strorage systems (cold and warm)
  • WRAS (BS 6920). A representative sample has passed the test (cold and warm)
  • W270: Microbiological growth test. A representative sample has passed the test
General  
Material Status 
  • Commercial: Active
Availability 
  • Africa & Middle East
  • Asia Pacific
  • Europe
  • Latin America
  • North America
Features 
  • Fast Cure
  • Food Contact Acceptable
  • Heat Cure
  • Low Odor
  • Medium Clarity
  • Non-Stick
Uses 
  • Industrial Applications
  • Non-specific Food Applications
  • Profiles
  • Tubing
 
Agency Ratings 
 
Appearance 
  • Clear/Transparent
Processing Method 
  • Extrusion
  • Profile Extrusion
 
Physical
Nominal Value
Unit
Test Method
Density
g/cm³
DIN 53479
Elastomers
Nominal Value
Unit
Test Method
Tensile Strength
psi
DIN 53504
Tensile Elongation (Break)
%
DIN 53504
Tear Strength 2
lbf/in
ASTM D624
Compression Set (347°F, 22 hr)
%
DIN 53517
Hardness
Nominal Value
Unit
Test Method
Durometer Hardness (Shore A)
 
DIN 53505
Thermoset
Nominal Value
Unit
Test Method
Thermoset Components
     
Part A
 
 
Part B
 
 
Pot Life
min
 
Shelf Life
wk
 
Post Cure Time (392°F)
hr
 
Additional Information
Nominal Value
Unit
Test Method
Vulcanization (347°F)
min
 
Features
Features may also be described by the following terms: Heat Cure, Medium Clarity, Non-sticky, not sticky, non-stick, Low Odor, Fast Cure, Fast Curing.
Uses
Uses may also be described by the following terms: Tubing, Tube, Food Applications.
Agency Ratings
This plastic material has 4 certifications from the following agencies (the number in parentheses shows the number of certifications for that agency): KTW (1), FDA (1), WRAS (1), BfR (1).
Available Documents
Technical Datasheet (English)
Notes
1Typical properties: these are not to be construed as specifications.
2Die B
 
UL and the UL logo are trademarks of UL LLC © 2020. All Rights Reserved.
The information presented here was acquired by UL from the producer of the product or material or original information provider. However, UL assumes no responsibility or liability for the accuracy of the information contained on this website and strongly encourages that upon final product or material selection information is validated with the manufacturer. This website provides links to other websites owned by third parties. The content of such third party sites is not within our control, and we cannot and will not take responsibility for the information or content.