Badamid® B70 S Datasheet

Polyamide 6

Supplied by Bada AG

Create your free Prospector account to view this complete product datasheet. A free account includes access to hundreds of thousands of detailed technical datasheets. Create Your Free Account
Product Description
Easy flowing injection moulding grade highly nucleated for short cycles
General  
Material Status 
  • Commercial: Active
Availability 
  • Europe
Additive 
  • Nucleating Agent
Features 
  • Good Flow
  • Nucleated
 
Forms 
  • Pellets
Processing Method 
  • Injection Molding
Physical
Dry
Conditioned
Unit
Test Method
Density
--
g/cm³
ISO 1183
Water Absorption
      ISO 62
Saturation, 73°F
--
%
 
Equilibrium, 73°F, 50% RH
--
%
 
Mechanical
Dry
Conditioned
Unit
Test Method
Tensile Modulus (73°F)
psi
ISO 527-2/1
Tensile Stress 2 (Yield, 73°F)
psi
ISO 527-2/50
Tensile Strain 2 (Yield, 73°F)
%
ISO 527-2/50
Nominal Tensile Strain at Break 2 (73°F)
%
ISO 527-2/50
Impact
Dry
Conditioned
Unit
Test Method
Charpy Notched Impact Strength 3
      ISO 179/1eA
-22°F
--
ft·lb/in²
 
73°F
--
ft·lb/in²
 
Charpy Unnotched Impact Strength 3 (73°F)
 
ISO 179/1eU
Notched Izod Impact Strength 3
      ISO 180/1A
-22°F
--
ft·lb/in²
 
73°F
--
ft·lb/in²
 
Thermal
Dry
Conditioned
Unit
Test Method
Heat Deflection Temperature 4
       
66 psi, Unannealed
--
°F
ISO 75-2/B
264 psi, Unannealed
--
°F
ISO 75-2/A
Melting Temperature (DSC) 5
--
°F
ISO 3146
CLTE - Flow  6 (0.157 in)
--
in/in/°F
DIN 53752
Maximum Service Temperature
      IEC 216
20000 hrs
--
°F
 
some hours
--
°F
 
Electrical
Dry
Conditioned
Unit
Test Method
Surface Resistivity 7
ohms
IEC 60093
Volume Resistivity 7
ohms·cm
IEC 60093
Electric Strength 7
V/mil
IEC 60243-1
Relative Permittivity 7 (1 MHz)
 
IEC 60250
Dissipation Factor 7 (1 MHz)
 
IEC 60250
Comparative Tracking Index
--
V
IEC 60112
Flammability
Dry
Conditioned
Unit
Test Method
Flame Rating 8 (0.06 in)
--
 
UL 94
Related Terminology
Dry
This supplier and product may also be known by these terms: PA6
Conditioned
This supplier and product may also be known by these terms: PA6
Generic Name
Dry
Generic Name may also be described by the following terms: PA6.
Conditioned
Generic Name may also be described by the following terms: PA6.
Features
Dry
Features may also be described by the following terms: Good Flow.
Available Documents
Dry
Technical Datasheet (English)
Conditioned
Technical Datasheet (English)
Injection
Dry
Unit
 
Drying Temperature
°F
 
Drying Time
hr
 
Processing (Melt) Temp
°F
 
Mold Temperature
°F
 
Notes
1Typical properties: these are not to be construed as specifications.
2Test Specimen accordng to ISO 3167, Type A
380x10x4 mm
4110x10x4mm
510 K/min, Compound for moulding
6>=10x10x4
780x80x1 mm
8125x13x1.6 mm
 
UL and the UL logo are trademarks of UL LLC © 2017. All Rights Reserved.
The information presented here was acquired by UL from the producer of the product or material or original information provider. However, UL assumes no responsibility or liability for the accuracy of the information contained on this website and strongly encourages that upon final product or material selection information is validated with the manufacturer. This website provides links to other websites owned by third parties. The content of such third party sites is not within our control, and we cannot and will not take responsibility for the information or content.