Product Description | |
Advanced Composites ADX-5001 is a Polypropylene product filled with 20% talc. It is available in North America. Typical application: Automotive. Primary characteristic: high flow.
|
|
General | |
Material Status
|
|
Availability
|
|
Filler / Reinforcement
|
|
Features
|
|
Uses
|
|
Automotive Specifications
|
|
Forms
|
|
Physical |
Nominal Value
|
Unit
|
Test Method
|
Density / Specific Gravity
|
|
|
ASTM D792 |
Melt Mass-Flow Rate (MFR) (230°C/2.16 kg)
|
|
g/10 min
|
ASTM D1238 |
Mechanical |
Nominal Value
|
Unit
|
Test Method
|
Tensile Strength (Yield)
|
|
psi
|
ASTM D638 |
Flexural Modulus
|
|
psi
|
ASTM D790 |
Impact |
Nominal Value
|
Unit
|
Test Method
|
Notched Izod Impact
|
ASTM D256 | ||
-22°F
|
|
ft·lb/in
|
|
73°F
|
|
ft·lb/in
|
|
Hardness |
Nominal Value
|
Unit
|
Test Method
|
Durometer Hardness (Shore D)
|
|
|
ASTM D2240 |
Thermal |
Nominal Value
|
Unit
|
Test Method
|
Deflection Temperature Under Load
|
ASTM D648 | ||
66 psi, Unannealed
|
|
°F
|
|
264 psi, Unannealed
|
|
°F
|
|
Related Terminology | |||
This supplier and product may also be known by these terms: Polypropilene, Polypropelene
|
|||
Generic Name | |||
Generic Name may also be described by the following terms: Polypropilene, Polypropelene.
|
|||
Features | |||
Features may also be described by the following terms: High Flow, High Melt, High MFI.
|
|||
Automotive Specifications | |||
This plastic material has approval for 1 automotive specifications from the following agencies (the number in parentheses shows the number of specifications for that agency): CHRYSLER (1).
|
|||
Available Documents | |||
PP/TPO Processing & Troubleshooting (English)
Processing (English) Technical Datasheet (English) |
Injection |
Nominal Value
|
Unit
|
|
Drying Temperature
|
|
°F
|
|
Drying Time
|
|
hr
|
|
Rear Temperature
|
|
°F
|
|
Middle Temperature
|
|
°F
|
|
Front Temperature
|
|
°F
|
|
Nozzle Temperature
|
|
°F
|
|
Processing (Melt) Temp
|
|
°F
|
|
Mold Temperature
|
|
°F
|
|
Cushion
|
|
in
|
|
Injection Notes | |||
Injection Pressure: 10% over max fill pressure
Holding Pressure: 50 to 60% of max fill pressure Injection Speed: 1 to 3 inches/sec Screw RPM: 1 to 2 secs before mold open |
Notes |
1Typical properties: these are not to be construed as specifications. |
UL and the UL logo are trademarks of UL LLC © 2021. All Rights Reserved.
The information presented here was acquired by UL from the producer of the product or material or original information provider. However, UL assumes no responsibility or liability for the accuracy of the information contained on this website and strongly encourages that upon final product or material selection information is validated with the manufacturer. This website provides links to other websites owned by third parties. The content of such third party sites is not within our control, and we cannot and will not take responsibility for the information or content. |