Epoxid (Epoxid) by BCC Products, Inc.
Produkt | Verfügbarkeit | Produktbeschreibung |
---|---|---|
BCC Products BC 6004 | Nordamerika |
BC 6004 is a white thixotropic epoxy surface coat that has the ability to cure and bond to freshly poured wet plaster. This formulated resin compound can be applied with a brush or troweled to a thickness of 1/8” or less on vertical surfaces or over sharp radii without sag or fear of run-off. BC 6004 features moderate heat resistance and tracing hardness.
|
BCC Products BC 6060 | Nordamerika |
BC 6060 is a blue epoxy, abrasion resistant surfacing resin. Commonly referred to as “die surface” material, this system may be applied by brush or if preferred, cast in thin sections to a maximum of ½”. Ideally suited for a variety of applications, BC 6060 is recommended for dies, foundry pattern and core boxes, router, trim and inspection fixtures.
|
BCC Products BC5114 | Nordamerika |
BC 5114 is a gray low viscosity laminating system. This heat resistant resin exhibits excellent wet out, reasonable working time and may be used at room temperature without post curing. For use above 150ºF a post-cure is required. BC 5114 can afford consistent use to 300ºF if required. Does not contain VCHD or MDA. Same uses as with BC 5105. See cure schedule.
|
BCC Products BC7009-1 | Nordamerika |
BC-7009-1 is an iron filled, low-cost mass casting system. Thicknesses up to two inches in non-conductive molds, and four inches in conductive molds can be achieved without foaming or yielding excessive shrinkage. Ideal for stretch forms, patterns, dies, molds, duplications, prototypes, etc.
|
BCC Products BC7009-2 | Nordamerika |
BC-7009-2 is an iron filled, low-cost mass casting system. Recommended for use in casting a minimum of two inches and a maximum of six inches in non-conductive molds. Thicknesses to nine inches in metal or conductive-type molds can successfully be achieved as well. Ideal for stretch forms, patterns, dies, molds, duplications, prototypes, etc.
|
BCC Products BC7062R/BC7062-2H | Nordamerika |
BC 7062 are aluminum filled, low viscosity epoxy mass casting resins. These room temperature cure systems allow the user choice thicknesses of 1/8 inch to a maximum of 6 inches without foaming or yielding excessive shrinkage. Casting thicknesses may be increased by incorporating aluminum needles, puffs or granules. BC 7062, when properly cured, provides nearly perfect reproduction, resulting in a dimensionally stable, hard, tough surface. For use in constructing duplicate models, prototypes, patterns, facing dies, etc.
|
BCC Products BC7062R/BC7062-3H | Nordamerika |
BC 7062 are aluminum filled, low viscosity epoxy mass casting resins. These room temperature cure systems allow the user choice thicknesses of 1/8 inch to a maximum of 6 inches without foaming or yielding excessive shrinkage. Casting thicknesses may be increased by incorporating aluminum needles, puffs or granules. BC 7062, when properly cured, provides nearly perfect reproduction, resulting in a dimensionally stable, hard, tough surface. For use in constructing duplicate models, prototypes, patterns, facing dies, etc.
|
BCC Products BC7062R/BC7062H | Nordamerika |
BC-7062 are aluminum filled, low viscosity epoxy mass casting resins. These room temperature cure systems allow the user choice thicknesses of 1/8 inch to a maximum of 6 inches without foaming or yielding excessive shrinkage. Casting thicknesses may be increased by incorporating aluminum needles, puffs or granules. BC-7062, when properly cured, provides nearly perfect reproduction, resulting in a dimensionally stable, hard, tough surface. For use in constructing duplicate models, prototypes, patterns, facing dies, etc.
|
BCC Products BE290 | Nordamerika |
BE-290 is a green low viscosity, medium pot life, room temperature laminating system. BE 290 features low odor, reduced toxicity and adequate working life for constructing medium and large fabricated tools.
|
BCC Products PolyPoxy ® 5105 | Nordamerika |
PolyPoxy ® 5105 is a clear, unfilled, low viscosity laminating system. This heat resistant resin exhibits excellent wet out, reasonable working time and may be used at room temperature without post-curing. For use above 150ºF a post-cure may be required. PolyPoxy ® 5105 can afford consistent use to 300ºF if required. Does not contain VCHD or MDA.
Useful for:
- Constructing vacuum form tools
- Injection and compression molds
- RTM and RIM molds
- Matched dies
|
BCC Products PolyPoxy® 5003 | Nordamerika |
PolyPoxy® 5003 Laminating Epoxy is a medium viscosity, unfilled laminating system. It is a room temperature curing resin with a relatively short pot life. BC 5003 is also considered an excellent general purpose adhesive for in-shop use. Recommended for use in gluing up BCC’s Tooling Board Series.
|
BCC Products PolyPoxy® 5008-2 | Nordamerika |
PolyPoxy® 5008-2 is a very low viscosity, modified, unfilled, room temperature curing, general purpose resin system. BC 5008-2 is a clear, amber, medium pot life material, with heat resistance to 175ºF. Also considered an excellent general purpose adhesive for in-shop use and will function as a laminating system for horizontal surfaces.
|
BCC Products PolyPoxy® 5010 | Nordamerika |
PolyPoxy® 5010 Laminating Epoxy is a high quality, low viscosity room temperature curing laminating resin. A Safety System for the production of a variety of dimensionally stable fiberglass tools. PolyPoxy® 5010 features low odor and rapid “wet-out” with no vertical drain off. An excellent general purpose laminating resin to meet the tooling requirements for automotive, aircraft and foundry.
|
BCC Products PolyPoxy® 6005 | Nordamerika |
BC 6005 is a snow white thixotropic epoxy resin designed specifically for quality reproduction of a variety of surfaces. A room temperature cure system that offers ample working time yet affords quick-tack for lamination. BC 6005 may be applied easily with a brush or troweled to a thickness of 1/8” or less on vertical surfaces or over sharp radii without sag or fear of run-off. When cured, this resin system provides a hard tough chip-resistant surface.
|
BCC Products PolyPoxy® 6126 | Nordamerika |
PolyPoxy® 6126 is a gray, low toxicity, aluminum filled, epoxy surface coat. This thixotropic resin system provides excellent surface duplication along with vertical coverage to 1/16 inch thickness. This heat resistant system may be used at room temperature without post-curing. For use above 150°F a post-cure is required. PolyPoxy® 6126 was engineered to replace VCHD and MDA systems while retaining excellent heat resistance. It is designed for consistent use up to 300°F. PolyPoxy® 6126 was developed for:
- Constructing vacuum form tools
- RTM and RIM molds
- Compression and injection molds
- Matched dies
|
BCC Products PolyPoxy® 7136 | Nordamerika |
PolyPoxy® 7136 is a gray, low toxicity, aluminum filled, epoxy casting resin. This heat resistant system may be used at room temperature without post-curing. May be cast to a thickness of ¾ inch in non-conductive molds. For use above 150ºF a post-cure is required. This product was engineered to replace VCHD and MDA systems while retaining excellent heat resistance and low viscosity. PolyPoxy® 7136 is designed for consistent use up to 300ºF. Useful for:
- Heat resistant tooling
- Constructing vacuum form tools
- Injection and compression molds
- RTM and RIM molds
- Matched dies
|
BCC Products PolyPoxy® 7136-2 | Nordamerika |
PolyPoxy® 7136-2 is an aluminum filled thick section casting system with heat resistance to 300ºF. May be cast to a thickness of 2 inches in non-conductive molds, 3 inches in conductive molds and thicker sections with the addition of bulk fill. For service temperature above 150ºF a post-cure is required. Does not contain VCHD or MDA. See cure schedule.
|