BC 6004 is a white thixotropic epoxy surface coat that has the ability to cure and bond to freshly poured wet plaster. This formulated resin compound can be applied with a brush or troweled to a thickness of 1/8” or less on vertical surfaces or over sharp radii without sag or fear of run-off. BC 6004 features moderate heat resistance and tracing hardness.

BC 6060 is a blue epoxy, abrasion resistant surfacing resin. Commonly referred to as “die surface” material, this system may be applied by brush or if preferred, cast in thin sections to a maximum of ½”. Ideally suited for a variety of applications, BC 6060 is recommended for dies, foundry pattern and core boxes, router, trim and inspection fixtures.

BC 5114 is a gray low viscosity laminating system. This heat resistant resin exhibits excellent wet out, reasonable working time and may be used at room temperature without post curing. For use above 150ºF a post-cure is required. BC 5114 can afford consistent use to 300ºF if required. Does not contain VCHD or MDA. Same uses as with BC 5105. See cure schedule.

BC-7009-1 is an iron filled, low-cost mass casting system. Thicknesses up to two inches in non-conductive molds, and four inches in conductive molds can be achieved without foaming or yielding excessive shrinkage. Ideal for stretch forms, patterns, dies, molds, duplications, prototypes, etc.

BC-7009-2 is an iron filled, low-cost mass casting system. Recommended for use in casting a minimum of two inches and a maximum of six inches in non-conductive molds. Thicknesses to nine inches in metal or conductive-type molds can successfully be achieved as well. Ideal for stretch forms, patterns, dies, molds, duplications, prototypes, etc.

BC 7062 are aluminum filled, low viscosity epoxy mass casting resins. These room temperature cure systems allow the user choice thicknesses of 1/8 inch to a maximum of 6 inches without foaming or yielding excessive shrinkage. Casting thicknesses may be increased by incorporating aluminum needles, puffs or granules. BC 7062, when properly cured, provides nearly perfect reproduction, resulting in a dimensionally stable, hard, tough surface. For use in constructing duplicate models, prototypes, patterns, facing dies, etc.

BC 7062 are aluminum filled, low viscosity epoxy mass casting resins. These room temperature cure systems allow the user choice thicknesses of 1/8 inch to a maximum of 6 inches without foaming or yielding excessive shrinkage. Casting thicknesses may be increased by incorporating aluminum needles, puffs or granules. BC 7062, when properly cured, provides nearly perfect reproduction, resulting in a dimensionally stable, hard, tough surface. For use in constructing duplicate models, prototypes, patterns, facing dies, etc.

BC-7062 are aluminum filled, low viscosity epoxy mass casting resins. These room temperature cure systems allow the user choice thicknesses of 1/8 inch to a maximum of 6 inches without foaming or yielding excessive shrinkage. Casting thicknesses may be increased by incorporating aluminum needles, puffs or granules. BC-7062, when properly cured, provides nearly perfect reproduction, resulting in a dimensionally stable, hard, tough surface. For use in constructing duplicate models, prototypes, patterns, facing dies, etc.

BE-290 is a green low viscosity, medium pot life, room temperature laminating system. BE 290 features low odor, reduced toxicity and adequate working life for constructing medium and large fabricated tools.

PolyPoxy ® 5105 is a clear, unfilled, low viscosity laminating system. This heat resistant resin exhibits excellent wet out, reasonable working time and may be used at room temperature without post-curing. For use above 150ºF a post-cure may be required. PolyPoxy ® 5105 can afford consistent use to 300ºF if required. Does not contain VCHD or MDA. Useful for: - Constructing vacuum form tools - Injection and compression molds - RTM and RIM molds - Matched dies

PolyPoxy® 5003 Laminating Epoxy is a medium viscosity, unfilled laminating system. It is a room temperature curing resin with a relatively short pot life. BC 5003 is also considered an excellent general purpose adhesive for in-shop use. Recommended for use in gluing up BCC’s Tooling Board Series.

PolyPoxy® 5008-2 is a very low viscosity, modified, unfilled, room temperature curing, general purpose resin system. BC 5008-2 is a clear, amber, medium pot life material, with heat resistance to 175ºF. Also considered an excellent general purpose adhesive for in-shop use and will function as a laminating system for horizontal surfaces.

PolyPoxy® 5010 Laminating Epoxy is a high quality, low viscosity room temperature curing laminating resin. A Safety System for the production of a variety of dimensionally stable fiberglass tools. PolyPoxy® 5010 features low odor and rapid “wet-out” with no vertical drain off. An excellent general purpose laminating resin to meet the tooling requirements for automotive, aircraft and foundry.

BC 6005 is a snow white thixotropic epoxy resin designed specifically for quality reproduction of a variety of surfaces. A room temperature cure system that offers ample working time yet affords quick-tack for lamination. BC 6005 may be applied easily with a brush or troweled to a thickness of 1/8” or less on vertical surfaces or over sharp radii without sag or fear of run-off. When cured, this resin system provides a hard tough chip-resistant surface.

PolyPoxy® 6126 is a gray, low toxicity, aluminum filled, epoxy surface coat. This thixotropic resin system provides excellent surface duplication along with vertical coverage to 1/16 inch thickness. This heat resistant system may be used at room temperature without post-curing. For use above 150°F a post-cure is required. PolyPoxy® 6126 was engineered to replace VCHD and MDA systems while retaining excellent heat resistance. It is designed for consistent use up to 300°F. PolyPoxy® 6126 was developed for: - Constructing vacuum form tools - RTM and RIM molds - Compression and injection molds - Matched dies

PolyPoxy® 7136 is a gray, low toxicity, aluminum filled, epoxy casting resin. This heat resistant system may be used at room temperature without post-curing. May be cast to a thickness of ¾ inch in non-conductive molds. For use above 150ºF a post-cure is required. This product was engineered to replace VCHD and MDA systems while retaining excellent heat resistance and low viscosity. PolyPoxy® 7136 is designed for consistent use up to 300ºF. Useful for: - Heat resistant tooling - Constructing vacuum form tools - Injection and compression molds - RTM and RIM molds - Matched dies

PolyPoxy® 7136-2 is an aluminum filled thick section casting system with heat resistance to 300ºF. May be cast to a thickness of 2 inches in non-conductive molds, 3 inches in conductive molds and thicker sections with the addition of bulk fill. For service temperature above 150ºF a post-cure is required. Does not contain VCHD or MDA. See cure schedule.