Nylene 4114 HS is a heat-stabilized, impact-modified nylon 6/6 molding resin with high impact strength and increased flexibility.

- Good flow characteristics - Nylene 4114 BK SP DSD is an impact-modified nylon 6/6 molding resin with high impact strength and increased flexibility.

- Impact-modified nylon 6,6 compounded copolymer, high melt point and increased flexibility. - Light stabilized for UV protection

Impact-modified nylon 6,6 compounded copolymer, high melt point and increased flexibility.

Nylene 4114-14 GL is an impact-modified molding resin with excellent impact strength.

- Nylene 4114-14 HSL is a glass fiber reinforced, impact modified, heat stabilized nylon 6/6. - Nylene 4114-14 HSL has improved strength and stiffness over un-reinforced nylons, and improved impact resistance over typical reinforced grades, especially in dry conditions.

Nylene 4114-14 is an impact-modified molding resin with excellent impact strength.

Nylene 4114-25 GF HRV is a compounded, 25% glass fiber-reinforced nylon 6/6 profile extrusion grade with excellent thermal stability.

Nylene 4114-33 GL HS is a compounded, heat-stabilized, impact-modified, 33% glass fiber-reinforced nylon 6/6 molding resin with excellent impact strength.

- Nylene 4114-33 HSL is a 33% glass fiber reinforced, impact modified, heat-stabilized nylon 6,6. - Nylene 4114-33 HSL is useful in applications which require the stiffness of 33% glass fiber reinforcement, but also benefit from improved toughness, especially in dry or cold environments.

Nylene 4120 HS is an impact-modified, heat-stabilized, nylon 6/6 molding resin with high impact strength. Free of silicones, it possesses very low wear properties.

Nylene 4120 is an impact-modified nylon 6/6 molding resin with high impact strength. While free of silicones, it possesses very low wear properties.

Nylene 4121 HS is an impact-modified, heat-stabilized, nylon 6/6 molding resin with high impact strength possessing excellent wear properties.

Nylene 4214-14 BK is a 14% glass fiber-reinforced, impact-modified nylon 6 with excellent molding characteristics and very good physical properties.

Impact-modified with excellent molding characteristics and very good physical properties

- Glass fiber reinforced, impact modified, heat stabilized nylon 6 - Suitable for applications which require this unique blend of properties - Improved strength and stiffness over unreinforced nylons, and improved impact resistance over typical reinforced grades, especially in dry conditions

- Glass fiber reinforced, impact modified, heat-stabilized nylon 6 - Useful in applications which require the stiffness of 33% glass fiber reinforcement, but also benefit from improved toughness, especially in dry or cold environments

Nylene 4214-40 HS is a 40% glass fiber-reinforced, heat-stabilized and impactmodified nylon 6 with excellent molding characteristics and very good physical properties.

- Dried to less than 0.20% moisture and packaged in foil-lined gaylords or bags to eliminate the need for pre-drying - Heat stabilized - Specially formulated nylon for the ROTOMOLDING process to reduce cost vs. using 100% powder. - For rotomolding, this product must be used in conjunction with Nylene® 494P BLK powder to achieve good part quality. - Chemical resistance to aromatic solvents, etc. especially at elevated temperatures - Custom colors on demand - Higher heat resistance and melting point. Not as likely to melt or lose shape if left in the sun. - Higher impact at room and elevated temperatures - Meets the strict CARB and EPA fuel permeation regulations - Permits a single step process and a single layer material fuel tank. This will reduce the chances of failure and scrap, which makes it extremely cost competitive

- Specially formulated, heat stabilized, nylon powder for the ROTOMOLDING process - Chemical resistance to aromatic solvents, etc. especially at elevated temperatures - Custom colors on demand - Higher heat resistance and melting point. Not as likely to melt or lose shape if left in the sun. - Higher impact at room and elevated temperatures - Meets the strict CARB and EPA fuel permeation regulations - Permits a single step process and a single layer material fuel tank. This will reduce the chances of failure and scrap, which makes it extremely cost competitive

- Specially formulated nylon powder for the ROTOMOLDING process. - For uses where HIGH IMPACT properties are required. - Dried to less than 0.20% moisture and packaged in foil-lined drums to eliminate the need for pre-drying. - Higher heat resistance and melting point. - Chemical resistance to aromatic solvents, etc. especially at elevated temperatures. - Excellent low temperature impact properties (Special impact modified products). - Higher impact at room and elevated temperatures. - Permits a single step process and a single layer material fuel tank. This will reduce the chances of failure and scrap, which makes it extremely cost competitive. - Meets the strict CARB and EPA fuel permeation regulations.

- 10 year UV stabilization package added for outdoor exposure protection. - Dried to less than 0.20% moisture and packaged in foil-lined drums to eliminate the need for pre-drying. - For uses where HIGH IMPACT properties are required. - Specially formulated nylon powder for the ROTOMOLDING process. - Chemical resistance to aromatic solvents, etc. especially at elevated temperatures. - UV resistance package increases end-use product life, protects against premature color fading, and retains appearance under weathering conditions for longer periods. - Permits a single step process and a single layer material fuel tank. This will reduce the chances of failure and scrap, which makes it extremely cost competitive. - Meets the strict CARB and EPA fuel permeation regulations. - Higher impact at room and elevated temperatures. - Higher heat resistance and melting point. - Excellent low temperature impact properties (Special impact modified products).

- Dried to less than 0.20% moisture and packaged in foil-lined drums to eliminate the need for pre-drying. - For uses where HIGH IMPACT properties are required. - Specially formulated nylon powder for the ROTOMOLDING process. - Chemical resistance to aromatic solvents, etc. especially at elevated temperatures - Excellent low temperature impact properties (Special impact modified products) - Higher heat resistance and melting point. Not as likely to melt or lose shape if left in the sun. - Higher impact at room and elevated temperatures - Permits a single step process and a single layer material fuel tank. This will reduce the chances of failure and scrap, which makes it extremely cost competitive

- Nylene powders for rotational molding are heat stabilized nylon 6 materials specially formulated for the rotational molding process. - Dried to less than 0.20% moisture and packaged in foil-lined drums to eliminate the need for pre-drying - Higher heat resistance and melting point. Not as likely to melt or lose shape if left in the sun. - Chemical resistance to aromatic solvents, etc. especially at elevated temperatures - Higher impact at room and elevated temperatures - Permits a single step process and a single layer material fuel tank. This will reduce the chances of failure and scrap, which makes it extremely cost competitive

- Nylene 5135 HS is a heat stabilized, 5% glass fiber-reinforced nylon 6/6 featuring high tensile strength and stiffness. - Suitable for applications where strength and stiffness are required. - Exhibits an improved impact resistance and flexibility over unmodified nylons

Nylene 5105 HS is a 5% glass fiber-reinforced nylon 6/6 featuring high tensile strength and stiffness.

Nylene 5110 HS is a 10% glass fiber-reinforced nylon 6/6 featuring high tensile strength and stiffness.

Heat stabilized, Glass fiber-reinforced nylon 6/6 featuring high tensile strength and stiffness

Heat stabilized, Glass fiber-reinforced nylon 6/6 featuring high tensile strength and stiffness

Nylene 5113 is a 13% glass fiber-reinforced nylon 6/6 featuring high tensile strength and stiffness.

Nylene 5115 HS is a 15% glass fiber-reinforced nylon 6/6 featuring high tensile strength and stiffness.

- Nylene 5120 HB Cool Grey is a 20% glass fiber-reinforced nylon 6/6 featuring flame retardant, high tensile strength and stiffness. - This product is recognized by Underwriters Laboratories.

Nylene 5120 HS is a 20% glass fiber-reinforced nylon 6/6 featuring high tensile strength and stiffness.

Nylene 5125 HS is a 25% glass fiber-reinforced nylon 6/6 featuring high tensile strength and stiffness.

- Nylene 5130 HR BK is a 30% glass fiber-reinforced nylon 6/6 featuring high tensile strength and stiffness. - Product is specially formulated to improve resistance to glycol, such as automotive engine cooling fluid. - Excellent thermal and mechanical properties to increase the lifetime of parts in constant contact with under the hood chemicals.

- Nylene 5130 HR NAT is a 30% glass fiber-reinforced nylon 6/6 featuring high tensile strength and stiffness. - Nylene 5130 HR NAT is specially stabilized to improve its resistance automotive cooling liquids. - Excellent thermal and mechanical properties to increase the lifetime of parts that are in constant contact with automotive chemicals.

Nylene 5130 HS is a 30% glass fiber-reinforced nylon 6/6 featuring high tensile strength and stiffness.

- Nylene 5130 MS is a low wear 30% glass fiber reinforced nylon 6,6 using molybdenum disulphide as a lubricant. - This material provides a low friction and low wear surface while maintaining the high strength and stiffness required from a glass fiber reinforced material. - 5130 MS is suitable for applications where wear may be an issue.

- Nylene 5130 PT15 is a low wear 30% glass fiber reinforced nylon 6/6 using 15% PTFE as a lubricant. - This material provides a low friction and very low wear surface while maintaining the high strength and stiffness required from a glass fiber reinforced material. - 5130 PT15 is suitable for applications where high strength with maximum wear resistance is required.

Nylene 5133 HRL is 33% glass fiber-reinforced nylon 6/6 with improved hydrolysis resistance, featuring high tensile strength and stiffness.