VESTAMID® D16 stabilized is a medium-viscosity Polyamide 612 compound for extrusion and injection moulding of e.g. monofilaments (toothbrush bristles). The material based on PA612 absorbs only small amounts of water. Components made of this material therefore show excellent dimensional stability under changing ambient humidity. Pigmentation may affect values.

VESTAMID® D16 is a medium-viscosity Polyamide 612 compound for extrusion and injection moulding of e.g. monofilaments (toothbrush bristles). The material based on PA612 absorbs only small amounts of water. Components made of this material therefore show excellent dimensional stability under changing ambient humidity. Pigmentation may affect values.

VESTAMID® D18 is a medium-viscosity Polyamide 612 compound for extrusion and injection moulding of e.g. monofilaments (toothbrush bristles). The material based on PA612 absorbs only small amounts of water. Components made of this material therefore show excellent dimensional stability under changing ambient humidity. Pigmentation may affect values.

VESTAMID® D22 is a high-viscosity Polyamide 612 compound for extrusion and injection moulding of e.g. films, monofilaments (abrasive bristles). The material based on PA612 absorbs only small amounts of water. Components made of this material therefore show excellent dimensional stability under changing ambient humidity. Pigmentation may affect values.

VESTAMID® DX9300 is a low-viscosity and heat-stabilized Polyamide 612 compound for injection moulding of e.g. retainers for quick connectors. The material based on PA612 absorbs only small amounts of water. Components made of this material therefore show excellent dimensional stability under changing ambient humidity. VESTAMID® DX9300 meets the requirements of the ISO 1874-PA612, MHR, 12-020. Pigmentation may affect values.

VESTAMID® DX9302 BK E70178 has been developed for the production of flexible, impact resistant extruded parts, especially tubes. Its composition makes VESTAMID® DX9302 BK E70178 suitable for the extrusion of tubes for windshield washer systems that have only small amounts of extractables substances in water/alcohol mixtures. Further advantages of VESTAMID® DX9302 BK E70178 are the typical properties of PA 612 like little water adsorption, good dimensional stability and almost constant mechanical properties at changing ambient humidity. Pigmentation may affect values.

VESTAMID® DX9303 BK E70288 is a PA 612 extrusion compound developed for the production of tubing systems with higher requirements for heat resistance. The melting point of VESTAMID® DX9303 BK E70288 is about 35°C higher than PA 11 and PA 12 compounds, allows higher peak temperatures in use. Thereby this compound fulfills the increased demands resulting from higher temperatures in the engine compartment. If it is intended to use VESTAMID® DX9303 BK E70288 for fuel lines, certain preconditions must be observed. The Technical Marketing assists you in finding the suitable VESTAMID® compound. At temperatures above 100°C tubing of VESTAMID® DX9303 BK E70288 allow a higher pressure load than tubing made of PA 12 compounds with comparable flexibility. The material absorbs only little moisture. Therefore dimensions and properties of parts are nearly unaffected through ambient conditions. Pigmentation may affect values.

VESTAMID® DX9304 BK E70238 is a PA 612 extrusion compound developed for the manufacturing of tubing systems with higher demands on heat resistance. The melting point of VESTAMID® DX9304 BK E70238, about 35 °C higher than PA 11 and PA 12 compounds, allows higher temperatures in use. The compound is especially suitable for the extrusion of tubing systems that are exposed to high burst pressures at high service temperatures, e.g. hydraulic clutch lines. The material absorbs only little moisture. Therefore dimensions and properties of parts are nearly unaffected through ambient conditions. Pigmentation may affect values.

VESTAMID® DX9305 BK E70335 is a black polyamide 612 extrusion compound developed for the manufacturing of tubing systems with higher demands on heat resistance. The melting range of VESTAMID® DX9305 BK E70335 of about 35 °C higher than PA 11 and PA 12 compounds allows higher peak temperatures in use. The compound is especially suitable for the extrusion of tubing systems that are exposed to high burst pressures at high service temperatures, e.g., hydraulic clutch lines. VESTAMID® DX9305 BK E70335 absorbs only little moisture. Therefore dimensions and properties of parts are nearly unaffected through ambient conditions. Pigmentation may affect values.

VESTAMID® DX9310 BK E70399 is a PA 612 extrusion compound developed for the production of tubing systems, for example multilayer tubes used as air brake lines. Besides optimized processing behavior and improved cold impact resistance VESTAMID® DX9310 BK E70399 offers, owing to a special modification, similar mechanical properties as VESTAMID® X7393 (PA 12 based compound typically used for monolayer air brake tubing). Due to these properties it is suited as middle layer in the multilayer tube 250.1, together with VESTAMID® X7393 as inner and outer layer. Pigmentation may affect values.

VESTAMID® DX9321 BK E70164 is a heat-stabilized, glass fiber-reinforced and impact-modified PA 612 compound. The material contains about 20% glass fibers, an ageing protective agent and processing aid for a fast and even form filling. VESTAMID® DX9321 BK E70164 is especially suitable for the production of plastic and rubber composites. Parts of VESTAMID® DX9321 BK E70164 can be directly bonded to rubber,e.g., XNBR, HNBR, AEM or FPM, without using any adhesives or adhesion promoters ("direct-bonding to rubber"). Because of its semi-crystalline morphology VESTAMID® DX9321 BK E70164 provides an excellent chemical resistance. e.g., against greases, oils, fuels and hydraulic fluids. Pigmentation may affect values

VESTAMID® DX9323 BK E70228 is a heat-stabilized, glass fiber-reinforced and impact-modified PA 612 compound. The material contains about 35% glass fiber, an ageing protective agent and processing aid for a fast and even form filling. VESTAMID® DX9323 BK E70228 is especially suitable for the production of plastic and rubber composites. Parts of VESTAMID® DX9323 BK E70228 can be directly bonded to rubber, e. g., XNBR, HNBR, AEM or FPM, without using any adhesives or adhesion promoters ("direct-bonding to rubber"). Because of its semi-crystalline morphology VESTAMID® DX9323 BK E70228 provides an excellent chemical resistance, e. g., against greases, oils, fuels and hydraulic fluids. Pigmentation may affect values.

VESTAMID® DX9325 BK E70352 is a glass fiber-reinforced, PA 612 molding compound. The material contains about 40% glass fiber, an ageing protective agent and processing aid for a fast and even form filling. VESTAMID® DX9325 BK E70352 is especially suitable for the production of plastic and rubber composites. Parts of VESTAMID® DX9325 BK E70352 can be co-vulcanized with EPDM-rubbers without using any adhesives or adhesion promoters ("direct-bonding to rubber"). Because of its semi-crystalline morphology VESTAMID® DX9325 BK E70352 provides an excellent chemical resistance, e. g., against greases, oils, fuels and hydraulic fluids. Pigmentation may affect values.

VESTAMID® DX9330 NC is a PA 612 base polymer without any stabilizers and other additives. VESTAMID® DX9330 NC is suitable for both extrusion as well as injection molding. Usually VESTAMID® DX9330 NC is only used in special cases when additives are not preferable, or processing aids are not necessary, e.g. filament extrusion. Based on the perfect balance of amino and carboxyl end groups this material is easy to process and to dye. The typical characteristics of PA 612 are moderate water absorption, good dimensional stability and almost unchanged properties at varying ambient humidity. Pigmentation may affect values.