Natural LDPE Formerly known as EnLene LDPE20

LD 250 Black is designed for thin film applications requiring good carbon black dispersion. It can be used for injection molding, blow molding, and sheet extrusion. The carbon black and base resin have been selected for good compatibility with most polyethylene film resins.

AXELERON™ CS 6005 NT CPD is a high-molecular weight, density polyethylene insulation compound ("CPD") with an excellent combination of mechanical and electrical properties which make it well suited for use as a primary dielectric. Specifications AXELERON™ CS 6005 NT CPD meets the following raw material specifications: - ASTM D 1248 IA-5, Grades E4 and E5 - Federal LP-390C II-L, Grade 3, Category 5 - MIL-C-17F, Amendment 1, Paragraph 3.5.2.1, Type A

AXELERON™ CX 0078 NT CPD is a nucleating agent masterbatch for the production of gas-injected cellular insulation for use in high performance coaxial cable. Typical end-use applications for the product include 75 ohm CATV distribution and trunk coaxial cable and large diameter 50 ohm RF coaxial cable used for mobile telephony. AXELERON™ CX 0078 NT CPD contains 10% of a low loss nucleating agent in a HP LDPE base resin. The masterbatch must be dry-blended with HDPE and LDPE base compounds ("CPD"), AXELERON™ CX 6944 NT CPD HDPE and AXELERON™ CX 1253 NT CPD LDPE respectively, prior to gas injection. For optimal foaming and cell structure, the nucleating agent concentration should range from 0.1-0.3% or 1-3% masterbatch in the blend. Since the compound exhibits excellent electrical properties, it is especially well suited to the production of heavy-wall (>7 mm insulation) foamed insulation. It is designed to offer superior processability and ease of foaming, allowing expansion rates of up to 80% to be achieved.

AXELERON™ CX 1253 NT CPD is a medium molecular weight, low density polyethylene insulation compound ("CPD") resin produced to a demanding set of electrical property specifications. DFDA-1253 Natural can be used as part of the resin system in the gas injection process for coaxial cable foamed insulation. Specifications AXELERON™ CX 1253 NT CPD meets the following raw material specifications: - ASTM D 1248 Type 1, Class A, Category 3 - Federal LP-390C Type 1, Class L, Grades 1 and 2, Category 3

AXELERON™ CX 1258 NT CPD is a medium molecular weight, low density polyethylene insulation compund ("CPD") for use in gas-injected foam insulation for coaxial/RF cables. AXELERON™ CX 1258 NT CPD can be used in combination with a high density polyethylene resin such as DGDA-6944 NT. To obtain optimal cellular structure, an additional 0.1% to 0.3% of a suitable nucleating agent is recommended, such as DFNA-0012 NT and DFNA-0078 NT masterbatches Main Characteristics - Low dissipation factor performance - Excellent compatibility with HDPE The polymeric material, using industry standard commercial extrusion practice, is compliant for use in Wire and Cable components that meet cable specification(s): - ASTM D 1248 Type 1, Class A, Category 3 Consult the regulations for complete details.

AXELERON™ CX 4960 NT CPD is an expandable, low-density polyethylene compound ("CPD") designed for use as insulation in applications requiring good cell structure and low electrical losses. It contains a temperature-sensitive blowing agent to provide a density between 0.40 and 0.48 g/cm³ when completely foamed. AXELERON™ CX 4960 NT CPD is widely used in coaxial applications, twin lead and CATV cables.

AXELERON™ CX A-0012 NT CPD is a masterbatch for use as a nucleating agent in gas-injection applications. It is specially designed for easy incorporation into our insulation compound ("CPD") AXELERON™ CX 6944 NT CPD HDPE and AXELERON™ CX 1253 NT CPD LDPE. When used correctly, it allows the formation of small, uniformly distributed cells. The masterbatch is a 10% concentrate of an exothermic chemical blowing agent in a high pressure LDPE base resin. It should be used at 0.1 to 0.3% nucleating agent or 1-3% masterbatch concentration. Typical applications include CATV drop cable type 59, 6, 7 and 11.

AXELERON™ GP C-0588 BK CPD is a prime quality telephone cable black jacketing compound ("CPD"). It offers excellent environmental stress-cracking resistance, outdoor weatherability, toughness, low temperature performance, and extrudability. AXELERON™ GP C-0588 BK CPD can be used by wire and cable manufacturers for the entire range of telephone cable sizes and configurations. It can be used for both air-core, and jelly-filled constructions, and in both aerial and buried applications. AXELERON™ GP C-0588 BK CPD can also be used as a high-grade power cable jacket. Specifications AXELERON™ GP C-0588 BK CPD meets the following raw material specifications: - ASTM D 1248 IC-5, Grades E5, J1, J3 - Federal LP-390C, III-L, Grades 2, 3 and 4, Category 5 - REA PE-22, 38, 39, 86, 89, 90 Cable jacketed with AXELERON™ GP C-0588 BK CPD, using sound commercial extrusion practices, should meet the following specifications: - ICEA: S-61-402; NEMA WC5 - ANSI: C8. 35 - ASTM: D 2308 - British Post Office Specification M-132G - Telcordia GR 421 Core - ANSI/ICEA S-84-608-1988

AXELERON™ GP D-0588 BK CPD, with a density of 0.93, and a melt index of 0.2, is a prime quality telephone telecom cable black jacketing compound ("CPD"). It offers excellent environmental stress cracking resistance, outdoor weatherability, toughness, low temperature performance, and extrudability. AXELERON™ GP D-0588 BK CPD can be used by wire and cable manufacturers for the entire range of telephone telecom cable sizes and configurations. It is suitable for both aircore and jelly-filled construction, and in both aerial and buried applications. Specifications AXELERON™ GP D-0588 BK CPD meets the following raw material specifications: - ASTM D 1248 IC-5 Grades, E5, J1 J3 - ISO 1872-1-PE, KCHL, 23-D003 - Federal LP-390 C, III-L, Grades 2,3, and 4, Category 5 - REA PE-22, 38, 39, 86, 89, 90 Cable jacketed with AXELERON™ GP D-0588 BK CPD using sound commercial extrusion practices, should meet the following specifications: - ICEA: S-61-402; NEMA WC 5 - ANSI: C8. 35 - ASTM: D 2308 - British Telecommunications plc M132 - Telcordia GR 421 Core - ANSI/ICEA S-84-608-1988 - EN 50290-2-24, grade LD - IEC 60708 - BS 6234: Type 03C, TS1

This resin is a multipurpose extrusion/injection low density polyethylene with excellent processability and good stiffness. This product meets US FDA 21 CFR 177.1520.

This resin is a medium flow general purpose injection molding low density polyethylene with good gloss, toughness and good chemical resistance. This product meets US FDA 21 CFR 177.1520.

This resin is a low density polyethylene for high speed extrusion coating applications that require superior adhesion and neck-in. This product meets US FDA 21 CFR 177.1520.

Bapolene 105B is a low density polyethylene for blown film applications. It complies with US FDA 21 CFR 177.1520.

This resin is an unmodified low density polyethylene which extrudes into a low gloss high impact film. It contains antiblock additives and no slip additives. This product meets US FDA 21 CFR 177.1520.

This resin is a high flow general purpose injection molding resin with good gloss, toughness and stress crack resistance. This product meets US FDA 21 CFR 177.1520.

Bapolene 1075 is a low density polyethylene for applications requiring a fast cycle time and modulus. It complies with US FDA 21 CFR 177.1520.

This resin is a low density polyethylene for blown film applications. It contains an antiblock additive. This product meets US FDA 21 CFR 177.1520.

This resin is a low density polyethylene for blown film. This product meets US FDA 21 CFR 177.1520.

This resin is a low density polyethylene for blown film applications and contains an antiblock additive. This product meets US FDA 21 CFR 177.1520.

This resin is a general purpose low density polyethylene for blown film extrsion applications requiring superior clarity. This product meets US FDA 21 CFR 177.1520.

This resin is a general purpose clarity low density polyethylene for blown film extrusion applications. It contains medium levels of slip/antiblock additives. This product meets US FDA 21 CFR 177.1520.

This resin is a low density polyethylene for blown film applications requiring superior clarity. It contains slip and antiblock additives. This product meets US FDA 21 CFR 177.1520. .

Bapolene 276F is a low density polyethylene for blown film applications. It contains slip and antiblocking additives and complies with US FDA 21 CFR 177.1520.

LE4147 is a low density thermoplastic polyethylene compound. It is well stabilized and has the same basic flow properties as the crosslinkable compound.

It is a low loss LDPE compound for coaxial cables. LE6006 contains a special type of antioxidant, which does not adversely affect the electrical properties. Applications LE6006 is intended for: - Bamboo constructed cables - Coaxial cables - Inner skin of radio frequency cables - Telephone wires Specifications LE6006 meets the following material classification: - ISO 1872-PE, KGHN, 18-D003 - ASTM D 1248 Type I, Class A, Category 5, Grade E4, E5 The following cable material standards are met by LE6006: - EN 50290-2-23 - DIN VDE 0207, 2YI3 Cables manufactured with LE6006 using sound extrusion practice normally comply with the following cable product standards: - IEC 61196 - EN 50117 Special Features LE6006 consists of specially selected components to offer: - Low dielectrical loss - Smooth surface - Excellent surface finish - High output

LE6022 is a black low density copolymer modified polyethylene compound. It is characterized by excellent stress crack resistance and mechanical properties and low temperature performance in combination with good extrudability. LE6022 contains 2,5% well dispersed furnace black in order to ensure excellent weathering resistance. Applications LE6022 is designed for jacketing of communication cables. Specifications LE6022 meets the applicable requirements as below when processed using sound extrusion practice and testing procedure: - ASTM D 1248 Type I, Class C, Category 5, Grade E5, J3, W2-4 - ISO 1872-PE, KCHL, 18-D003 The following cable material standards are met by LE6022: - EN 50290-2-24 - DIN VDE 0207 Type 2YM2 Cables manufactured with LE6022 using sound extrusion practice normally comply with the following cable product standards: - IEC 60502, Part 2, Type ST3 - IEC 60708 - IEC 60840, Type ST3 - HD 620 S2, Part 1, table 4B, DMP 17

LE6025 is a black low density copolymer modified polyethylene compound. It is characterized by excellent stress crack resistance and mechanical properties and low temperature performance in combination with good extrudability. LE6025 contains 2,5 % well dispersed furnace black in order to ensure excellent weathering resistance. Applications LE6025 is designed for jacketing of energy and communication cables. Specifications LE6025 meets the applicable requirements as below when processed using sound extrusion practice and testing procedure: - ISO 1872-PE, KCHL, 18-D003 - ASTM D 1248 Type I, Class C, Category 5, Grade E5, J3, W2-4 The following cable material standards are met by LE6025: - EN 50290-2-24 Cables manufactured with LE6025 using sound extrusion practice normally comply with the following cable product standards: - IEC 60502, Part 2, Type ST3 - IEC 60840, Type ST3 - HD 603 S1, DMP 7, 8 - HD 620 S2, Part 1, table 4B, DMP 10, 12, 14, 17

CA7230 is a low-density polyethylene for extrusion coating. CAS-No.: 9002-88-4 Applications CA7230 is designed for: - Extrusion coating of high volume production of boards and papers - Coating and lamination of aluminium foil - Co-extrusion applications - Coating of various plastic films and cellophane Additives - CA7230 contains no additives. Special features CA7230 is optimised to deliver: - Good water vapour barrier - Extremely low odour during processing

CA8200 is a low-density polyethylene for extrusion coating. CAS-No.: 9002-88-4 Applications CA8200 is designed for: - Extrusion coating of high volume production of boards and papers - Coating of various plastic films and cellophane Additives - CA8200 contains no additives. Special features CA8200 is optimised to deliver: - Good moisture barrier properties - Good adhesion properties - Good heat seal properties - Very low odour during processing

CA9150 is a low-density polyethylene for extrusion coating. CAS-No.: 9002-88-4 Applications CA9150 is designed for: - Coating and lamination of aluminium foil - Extrusion coating of high volume production of boards and papers - Coating of various plastic films and cellophane Additives - CA9150 contains no additives.

CC7209 is an extrusion coating grade especially designed for seal-peel applications. It gives smooth and easy peel when sealed against itself and PE. CC7209 provides also good adhesion to various substrates, particularly to aluminium. The rocommendation is to mix it with standard LDPE with the ratio 1:1 In this mixture processing like standard LDPE can be applied. The material must be pre-dried but there can be still a slight risk for filter blocking and filler agglomeration. CC7209 contains 30 percent finely dispersed filler CAS-No.: 9002-88-4 Applications CC7209 is recommended for: - extrusion coated seal-peel structures - Food packaging - tie layer for aluminium in extrusion coated/laminated structures Additives CC7209 contains finely dispersed filler but no other additives.

CT7200 is a low-density polyethylene homopolymer for extrusion coating, produced with high pressure tubular technology. CAS-No. 9002-88-4

FA3221 is a Low Density Polyethylene for Film Extrusion. Autoclave Technology. Includes Antioxidant. This grade is developed to give a strong film with balanced shrink properties. Applications FA3221 has been developed especially for applications like: - Heavy-duty sack - Food packaging - Agricultural films - Construction films - Shrink film Additives FA3221 contains antioxidant.

FA3227 is a low density polyethylene produced in a high-pressure process. FA3227 is a Low Density Polyethylene for Film Extrusion, UV stabilised. This grade is suitable for building and construction film and meets the requirements for heat, alkali and UV resistance described in the building standards from the Nordic countries. A 150-micron film based upon FA3227 will last at least four times as long as an unstabilised film of the same thickness. CAS-No.: 9002-88-4 Applications FA3227 has been developed especially for applications like: - Construction films - Shrink film - Heavy-duty sack - Liners Additives - FA3227 is UV stabilised.

FA5223 is a Low Density Polyethylene for Film Extrusion. Autoclave Technology. Contains Antioxidant and Anti-block additive. This grade is developed to give strong film for medium duty applications. CAS-No.: 9002-88-4 Applications FA5223 has been developed especially for applications like: Heavy-duty sack - Carrier-bag film - Food packaging - Pouches - Shrink film - General packaging film Additives Content Antiblock (Talc) 850 ppm Borealis Method Antioxidant Yes Borealis Method

FA5224 is a Low Density Polyethylene for Film Extrusion. Autoclave Technology. Contains Antioxidant, Anti-block and Medium Slip additives. This grade is developed to give strong film for medium duty applications. CAS-No.: 9002-88-4 Applications FA5224 has been developed especially for applications like: - Carrier-bag film - General packaging film - Pouches Additives Content Antiblock (Talc) 850 ppm Borealis Method Slip (Erucamide) 450 ppm Borealis Method Antioxidant Yes Borealis Method