Prospector

Polyphénylène sulfure (PPS) by Envalior

Produit Disponibilité Description du produit
Tepex® 207-C200(x)/50% Afrique & Moyen-Orient
Tepex® dynalite 207-C200(x)/50%3K Carbon - PPS consolidated composite laminate The datasheet is valid for this specific composition only, the characteristics of composites depend on reinforcement level and fiber orientation. Non-standard thickness may alter some or all of these properties. The data listed here are given as average product properties and should not be used to establish specification limits nor used alone as basis of design. The underlying tests were conducted at room temperature and (where possible) with 2 mm specimen thickness. For tensile and flexural tests a specimen width of 25 mm was used and is highly recommended to achieve representative results.
Xytron™ G3010E Afrique & Moyen-Orient
30% Glass Reinforced, High Impact, Food Contact Quality, Drinking Water Grade Design Challenge Degradation & Stability | Chemical stability
Xytron™ G3020DW-FC Afrique & Moyen-Orient
30% Glass Reinforced, Drinking Water Grade, Food Contact Quality, Flame Retardant Design Challenge Degradation & Stability | Chemical stability
Xytron™ G3020T Afrique & Moyen-Orient
30% Glass Reinforced, Flame Retardant Design Challenge Degradation & Stability | Chemical stability
Xytron™ G3080R Afrique & Moyen-Orient
30% Glass Reinforced, Flame Retardant, Excellent Mold Release, Low Flash Design Challenge Degradation & Stability | Chemical stability
Xytron™ G4010E Afrique & Moyen-Orient
40% Glass Reinforced, Improved Impact Design Challenge Degradation & Stability | Chemical stability
Xytron™ G4010T Afrique & Moyen-Orient
40% Glass Reinforced, Flame Retardant, Improved flow Design Challenge Degradation & Stability | Chemical stability
Xytron™ G4010W Afrique & Moyen-Orient
40% Glass Reinforced, Wear and Friction Modified, Flame Retardant Design Challenge Degradation & Stability | Chemical stability
Xytron™ G4012T Afrique & Moyen-Orient
40% Glass Reinforced, Halogen free, Chlorine Content < 900 ppm Design Challenge Degradation & Stability | Chemical stability
Xytron™ G4020DW-FC Afrique & Moyen-Orient
40% Glass Reinforced, Drinking Water Grade, Food Contact Quality, Flame Retardant Design Challenge Degradation & Stability | Chemical stability
Xytron™ G4020T Afrique & Moyen-Orient
40% Glass Reinforced, Flame Retardant Design Challenge Degradation & Stability | Chemical stability
Xytron™ G4024T/A Afrique & Moyen-Orient
40% Glass Reinforced, Excellent Mold Release, Flame Retardant
Xytron™ G4024T Afrique & Moyen-Orient
40% Glass Reinforced, Excellent Mold Release, Flame Retardant Design Challenge Degradation & Stability | Chemical stability
Xytron™ G4080HR Afrique & Moyen-Orient
40% Glass Reinforced, Flame Retardant, Hydrolysis resistant Design Challenge Degradation & Stability | Chemical stability
Xytron™ G4080HRE Afrique & Moyen-Orient
Design Challenge Degradation & Stability | Chemical stability
Xytron™ M5710T Afrique & Moyen-Orient
Flame Retardant, Enhanced Mechanical Strength, Excellent Dimensional Stability Design Challenge Degradation & Stability | Chemical stability
Xytron™ M6510A Afrique & Moyen-Orient
65% Glass/Mineral Reinforced, Flame Retardant, Excellent Dimensional Stability Design Challenge Degradation & Stability | Chemical stability
Xytron™ TC6022I Afrique & Moyen-Orient
Thermal conductive material Design Challenge Degradation & Stability | Chemical stability
Xytron™ U1535E Afrique & Moyen-Orient
Unreinforced, Extrusion Design Challenge Degradation & Stability | Chemical stability
Xytron™ U3020E Afrique & Moyen-Orient
Extrusion, Improved Impact Despite the fact that the above-mentioned grade is an extrusion grade, when using it for an injection molding process, the document below describes the typical injection molding recommendations. Design Challenge Degradation & Stability | Chemical stability
1
1