Alkatuff LL755 is a hexene LLDPE material specifically designed for rotational moulding applications that require excellent ESCR, chemical resistance, stiffness and toughness. Alkatuff LL755 does not contain UV stabiliser. Alkatuff LL755 is a general purpose rotational moulding grade, uses of which include water and agricultural tanks, leisure craft and playground equipment. For outdoor applications, an appropriate UV stabilisation package should be added. Alkatuff LL755 complies with the non UV base resin requirements of AS/NZS 4766 Rotationally moulded buried, partially buried and non-buried storage tanks for water and chemicals.

Alkatuff LL820 is a high flow hexene copolymer linear low density polyethylene designed for general purpose injection moulding. Alkatuff LL820 is intended for general purpose injection moulding such as housewares and lids.

BD24250AA is a linear low density polyethylene copolymer containing butene-1 as a co-monomer. BD24250AA is suitable for high flow injection moulding applications such as house wares, boxes and closures. The superior stress crack resistance makes it particularly good for caps and closures. * BD24250AA is suitable for food contact.

LL0209AA & LL0209KJ are linear low density polyethylene copolymers containing butene-1 as a co-monomer. LL0209AA & LL0209KJ are suitable for general purpose films, neat or in lean blends with LDPE and other ethylene polymers. Lean blends applications include sacks of all types, FFS and agricultural films. In lean blends they offer the following advantages: - Greater draw down. - Improved hot-tack and lower seal shrinkage. - Better tear resistance. - Higher tensile stress and elongation at break. LL0209KJ offers high slip film with easy opening properties when used pure in thickness range 35-100 microns. Addition of other polymers, master batches and pigments or use of other thickness may alter film slip and anti-block performance. If corona treatment is necessary, the level should normally be in the range 38-48 mN/m. LL0209AA & LL0209KJ should be stored in the dry condition below the 50°C and avoided from the exposure of direct sunlight. Recommended melt temperature for extrusion is about 180°C - 225°C. * LL0209AA & LL0209KJ are suitable for food contact.

LL0209CA is a linear low density polyethylene copolymer containing butene-1 as a co-monomer. LL0209CA is suitable for stretch wrap blown films neat or in lean blend with LDPE products. LL0209CA shows good puncher resistance and cling performance. Typical melt temperature range in extruder is about 180°C - 220°C. LL0209CA should be stored in the dry condition below the 50°C and avoided from the exposure of direct sunlight.

LL0220AA is a linear low density polyethylene copolymer containing butene-1 as a co-monomer. LL0220AA has been specially developed for production of hand wrap and other cast stretch films such as oriented tapes. It can also be used as a blending partner in LDPE or LLDPE in both cast and blown film applications. LL0220AA offers the following advantages when it processed by the cast extrusion process: - Good balance of mechanical properties. - Good optical properties. - Good cling performance. LL0220AA also can be used as compounds for low voltage power cable insulation or fibre optic jacketing. LL0220AA should be processed in machinery designed for LLDPE. Melt temperature range in the cast process are normally 240°C-280°C and in lean blends for blown film are 165°C-215°C. LL0220AA should be stored in the dry condition below the 50°C and avoided from the exposure of direct sunlight. * LL0220AA is suitable for food contact.

LL0220CA is a linear low density polyethylene copolymer containing butene-1 as a co-monomer. LL0220CA is suitable for production of cast stretch films. It can also be used as a blending partner in LDPE or LLDPE in both cast and blown film applications. The main characteristic of this grade is high TD tear strength that appropriates it for stretch applications. LL0220CA also can be used as compounds for low voltage power cable insulation or fibre optic jacketing. LL0220CA should be processed in machinery designed for LLDPE. Melt temperature range in the cast process are normally 240°C-280°C and in lean blends for blown film are 165°C-215°C. LL0220CA should be stored in the dry condition below the 50°C and avoided from the exposure of direct sunlight. * LL0220CA is suitable for food contact.

LL0410AA & LL0410KJ are linear low density polyethylene copolymers containing butene-1 as a co-monomer. LL0410AA & LL0410KJ are suitable for thin and stiff blown films because of their good draw down properties. LL0410AA also can be used for applications such as carrier bags and garment wraps. LL0410KJ contains slip and anti-blocking agents for better opening properties. Recommended melt temperature for extrusion is about 180°C - 225°C. LL0410AA & LL0410KJ should be stored in the dry condition below the 50°C and avoided from the exposure of direct sunlight. * LL0410AA & LL0410KJ are suitable for food contact.

LL0640AA & LL0640KJ are linear low density polyethylene copolymers containing butene-1 as a co-monomer. LL0640AA & LL0640KJ have been specially designed for the production of high quality cast films, such as display packaging, bubble film and non cling layer for stretch film. LL0640AA & LL0640KJ have the following advantages: - High melt flow rate for high output cast extrusion. - Excellent combination of strengths and stiffness. - High gloss and clarity. If corona treatment is necessary, the level should normally be in the range 38-48 mN/m. Melt temperature range in the cast process are normally 220°C-260°C and in lean blends for blown film are 160°C-215°C. LL0640AA & LL0640KJ should be stored in the dry condition below the 50°C andavoided from the exposure of direct sunlight. * LL0640AA & LL0640KJ are suitable for food contact.

LL1209AA & LL1209KJ are linear low density polyethylene copolymers containing butene-1 as a co-monomer. LL1209AA & LL1209KJ are suitable for co extrusion blown films with the following advantages: - Improved hot-tack. - Good optical properties. - Low gel level and low odour. - Good substrate adhesion. - Tough core layer. Typical applications for LL1209AA & LL1209KJ are lamination films and heat sealing layers. Also LL1209KJ is highly recommended for display packaging. LL1209KJ offers high slip film with easy opening properties when used pure in thickness range 35-100 microns. Addition of other polymers, master batches and pigments or use of other thickness may alter film slip and anti-block performance. Recommended melt temperature for extrusion is about 180°C-225°C. LL1209AA & LL1209KJ should be stored in the dry condition below the 50°C and avoided from the exposure of direct sunlight. * LL1209AA & LL1209KJ are suitable for food contact.

ASPUN 6834 Fiber Grade Resin is a product suitable for use in staple fiber and spunbond production equipment (Mono and Bico configuration). Commercial uses are in the non-woven areas offering excellent softness and drapability, direct thermal bonding of fabric to fabric or fabric to polyethylene film. Commercially in Staple Fibers it is used for low bonding fibers as bicomponent sheath. Note: ASPUN 6834 Fiber Grade Resin should comply with FDA regulation 177.1520 and with most European food contact regulations when used unmodified and processed according to good manufacturing practices for food contact applications. Please, contact your nearest Dow office for food contact compliance statements. The purchaser remains responsible for determining whether the use complies with all relevant regulations. Applications: - Housewares - Textiles & Fibers - Health & Hygiene - Automotive Interiors - Medical Packaging

- Designed for processing into yarn and bonding fibers - Complies with U.S. FDA 21 CFR 177.1520 (c) 3.2a. - Consult the regulations for complete details. ASPUN™ 6835A Fiber Grade Resin is a linear low density polyethylene (LLDPE). A typical process is staple fiber production.

ASPUN* 6840A Fiber Grade Resin is a linear low density polyethylene (LLDPE). A typical process is spunbond non-woven or staple fiber production - Is designed for processing into nonwoven fabrics and nonwoven fibers - Soft fabric with excellent drape - Low melting point for bonding Complies with: - US. FDA 21 CFR 177.1520(c)3.1A Consult the regulation for complete details.

Aspun™ 6850 Fiber Grade Resin is a linear low density polyethylene (LLDPE). Typical processes include spun-bond nonwoven and staple fiber production. Characteristics: Designed for processing into nonwoven fabrics and bonding fibers. Soft fabric with excellent drape. Low melting point for bonding. It complies with: - U.S. FDA 21 CFR 177.1520 (c) 3.2a - EU, No 10/2011 Consult the regulations for complete details. Notes: The composition of this product complies with the requirements for use in contact with food of the EU, No 10/2011. Contact a Dow Sales Office to obtain a detailed food contact compliance letter for this product. Such a letter covers the food contact status of this product in the various European Countries and in addition gives information about the imposed migration requirements.

ASPUN™ 6850A Fiber Grade Resin is a product suitable for use in staple fiber and spunbond production equipment. Commercial uses are in the non-woven areas offering excellent softness and drapability, low bonding temperature, direct thermal bonding of fabric to fabric or fabric to polyethylene film. Complies with: - U.S. FDA 21 CFR 177.1520 (c) 3.2a - EU, No 10/2011 Consult the regulations for complete details. Notes: The composition of this product complies with the requirements for use in contact with food of the EU, No 10/2011. Contact a Dow Sales Office to obtain a detailed food contact compliance letter for this product. Such a letter covers the food contact status of this product in the various European Countries and in addition gives information about the imposed migration requirements.

ASPUN™ AT 2135 Fiber Grade Resin is a product suitable for use in staple fiber and spunbond production equipment. Commercial uses are in the non-woven areas offering excellent softness and drapability, low bonding temperature, direct thermal bonding of fabric to fabric or fabric to polyethylene film. Complies with: - U.S. FDA 21 CFR 177.1520 (c) 3.2a - EU, No 10/2011 Consult the regulations for complete details. Notes: The composition of this product complies with the requirements for use in contact with food of the EU, No 10/2011. Contact a Dow Sales Office to obtain a detailed food contact compliance letter for this product. Such a letter covers the food contact status of this product in the various European Countries and in addition gives information about the imposed migration requirements.

Asrene® UC1827 is a LLDPE resin recommended for the production of low voltage insulation cured using the on-step silane-grafting moisture-crosslinking technology process. This grade offers good surface appearance, smooth extrusion process and does not contain any slip and antiblock additives. Product Characteristics: - Butene copolymer - Barefoot - Good thermal stability Applications: - Low voltage wire insulation - Low voltage power cable jacketing

Asrene® UF1810 is an LLDPE resin which is supplied in natural pellet form and suitable for cast and blown film, multi-layer film requiring high clarity, good toughness and low gel content. Product Characteristics: - Barefoot - Butene copolymer - High clarity and low gel content - Good toughness Applications: - Cast and blown film - Multi-layer film

Asrene® UF1810S1 is an LLDPE resin which is supplied in natural pellet form and suitable for blown film, agriculture film, various bags from narrow to broad film width and inner liners requiring good impact strength, excellent open-ability and process-ability. Product Characteristics: - Butene copolymer - Excellent open-ability and process-ability - Good impact strength - High anti-block - Contain slip agent Applications: - Blown film - Garbage, ice mambo and shopping bags - Inner liners - Agriculture film

Asrene® UF1810T is an LLDPE resin which is supplied in natural pellet form and suitable for blown films, cover sheets and transparent films, inner liners, garment sacks and rice bags requiring high clarity, good impact strength, toughness and openability. Product Characteristics: - Butene copolymer - High clarity - Good impact strength, toughness and open-ability - Medium anti-block - Contain slip agent Applications: - Blown films - Cover sheets and transparent films - Inner liners - Garment sacks and rice bags

Asrene® UF1820 is an LLDPE resin which is supplied in natural pellet form and suitable for stretch, cast, blown and multi-layer film requiring high clarity, low gel content and good toughness. Product Characteristics: - Barefoot - Butene copolymer - High clarity and low gel content - Good toughness - Cling-ability Applications: - Stretch film - Cast and blown film - Multi-layer film

Asrene® UF1820S1 is an LLDPE resin which is supplied in natural pellet form and suitable for blown, agriculture and multi-layer film, various bags and inner liners requiring good impact strength, excellent openability and process-ability. Product Characteristics: - Butene copolymer - Excellent openability and process-ability - Good impact strength - High anti-block - Contain slip agent Applications: - Blown film - Agriculture and multi-layer film - Inner liners

Asrene® UF1820T is an LLDPE resin which is supplied in natural pellet form and suitable for blown and transparent film, cover sheet, inner liner, garment sack and rice bags requiring high clarity, good impact strength, good toughness and openability. Product Characteristics: - Butene copolymer - High clarity - Good impact strength - Medium anti-block - Contain slip agent - Good toughness and openability Applications: - Blown film - Cover sheet - Garment sack - Inner liners - Rice bags - Transparent film

Asrene UF1810MH is an ethylene-hexene copolymer LLDPE resin made by metallocene catalyst which is supplied in natural pellet form and suitable for blown film, multi-layer film and specialty packaging film applications that require high clarity, exceptional toughness and outstanding heat seal. TnPP is not intentionally added to UF1810MH. Product Characteristics: - Barefoot (no slip, no antiblock) - TnPP free - Processing aid - Thermal stabilizer - Narrow MWD Applications: - Blown film - Stretch film - Multilayer packaging film - FFS and heavy-duty packaging - Lamination film

Asrene UF1810MT is an ethylene-hexene copolymer LLDPE resin made by metallocene catalyst which is supplied in natural pellet form and suitable for blown film, multi-layer film and specialty packaging film applications that require high clarity, exceptional toughness and outstanding heat seal. TnPP is not intentionally added to UF1810MT. Product Characteristics: - Antiblock-Slip - TnPP free - Processing aid - Thermal stabilizer - Narrow MWD Applications: - Blown film - Stretch film - Multilayer packaging film - FFS and heavy-duty packaging - Lamination film

Asrene UF1820MH is an ethylene-hexene copolymer LLDPE resin made by metallocene catalyst which is supplied in natural pellet form and suitable for blown film, multi-layer film and specialty packaging film applications that require high clarity, exceptional toughness and outstanding heat seal. TnPP is not intentionally added to UF1820MH. Product Characteristics: - Barefoot (no slip, no antiblock) - TnPP free - Processing aid - Thermal stabilizer - Narrow MWD Applications: - Blown film - Stretch film - Multilayer packaging film - FFS and heavy-duty packaging - Lamination film

Asrene UF1820MT is an ethylene-hexene copolymer LLDPE resin made by metallocene catalyst which is supplied in natural pellet form and suitable for blown film, multi-layer film and specialty packaging film applications that require high clarity, exceptional toughness and outstanding heat seal. TnPP is not intentionally added to UF1820MT. Product Characteristics: - Antiblock-Slip - TnPP free - Processing aid - Thermal stabilizer - Narrow MWD Applications: - Blown film - Stretch film - Multilayer packaging film - FFS and heavy-duty packaging - Lamination film

Asrene UF1835MH is an ethylene-hexene copolymer LLDPE resin made by metallocene catalyst which is supplied in natural pellet form and suitable for blown film, cast film and specialty packaging film applications that require excellent impact, exceptional toughness and outstanding heat seal. TnPP is not intentionally added to UF1835MH. Product Characteristics: - Barefoot (no slip, no antiblock) - TnPP free - Processing aid - Thermal stabilizer - Narrow MWD Applications: - Blown Film - Cast Film - Cast Stretch Film - Form Fill and Seal Packaging

Asrene® UI2420 is an LLDPE resin which is supplied in natural pellet form and suitable for injection molding, lids and bottle closures, masterbatch and powder coating, toys, housewares and trash cans requiring high flow properties, excellent mold-ability and toughness. Product Characteristics: - Excellent mold-ability - Excellent toughness - Medium flow properties - Non UV stabilized Applications: - Injection molding - Lids and bottle closures - Masterbatch and powder coating - Toys, housewares and trash cans

Asrene® UI2650 is an LLDPE resin which is supplied in natural pellet form and suitable for injection molding, lids and bottle closures, master batch, powder coating and toys requiring high flow properties, excellent mold-ability, toughness and ESCR. Product Characteristics: - Excellent mold-ability - Excellent toughness and ESCR - High flow properties - Non UV stabilized Applications: - Injection molding - Lids and bottle closures - Masterbatch and powder coating - Toys

Specialty black concentrate designed for use in the manufacturing of PE pressure pipes. Suitable for use with polyethylene and polypropylene resins in pipe and other profile extrusions.

This concentrate is designed for polyethylene film. It can also be used for sheet extrusion, blow molding and injection molding. It can be used with all polyolefin resins(LDPE, LLDPE, HDPE, and PP).

This concentrate is designed for polyethylene film. It can also be used for sheet extrusion, blow molding and injection molding. It can be used with all polyolefin resins(LDPE, LLDPE, HDPE, and PP).

This concentrate is designed for polyethylene film. It can also be used for sheet extrusion, blow molding and injection molding. It can be used with all polyolefin resins(LDPE, LLDPE, HDPE, and PP).

This concentrate is designed for polyethylene film. It can also be used for sheet extrusion, blow molding and injection molding. It can be used with all polyolefin resins(LDPE, LLDPE, HDPE, and PP).

LL 250 Black is designed for thin film applications requiring good carbon black dispersion. It can be used for injection molding, blow molding, and sheet extrusion. The carbon black and base resin have been selected for good compatibility with most polyethylene film resins.

Black masterbatch with an LLDPE carrier resin, suitable for use with polyethylene and polypropylene resins.

Black masterbatch with an LLDPE carrier resin, suitable for use with polyethylene and polypropylene resins for injection molding.

This concentrate is designed for polyethylene film, including very thin gauges. It can also be used for sheet extrusion, blow molding and injection molding. It can be used with all polyolefin resins(LDPE, LLDPE, HDPE, and PP).

Black masterbatch with an LLDPE carrier resin, suitable for use with polyethylene and polypropylene resins for injection molding.