NEOFLON PCTFE M-300P is a high hardness fluororesin with excellent gas barrier properties. Introduction - NEOFLON PCTFE M-300P is a polymer with a structure in which all hydrogen atoms of polyvinyl chloride (CH 2 --CHCl) n are substituted with fluorine atoms. It is in the form of one chlorine atom in PTFE structural unit. - Highly transparent due to this chlorine atom. - It is a fluororesin with the highest gas barrier property and high hardness. - Excellent in mechanical properties, although it is slightly inferior to PFA and FEP in heat resistance and chemical resistance. - M-300P is a pelletized product which is suitable for both compression and extrusion molding.

NEOFLON PCTFE M-300PL is a high hardness fluororesin with excellent gas barrier properties. Introduction - NEOFLON PCTFE M-300PL is a polymer with a structure in which all hydrogen atoms of polyvinyl chloride (CH 2 --CHCl) n are substituted with fluorine atoms. It is in the form of one chlorine atom in PTFE structural unit. - Highly transparent due to this chlorine atom. - It is a fluororesin with the highest gas barrier property and high hardness. - Excellent in mechanical properties, although it is slightly inferior to PFA and FEP in heat resistance and chemical resistance. - M-300PL is a pelletized product with higher molecular weight than M-300P. - Excellent in stress crack resistance. It is suitable for both compression and extrusion molding.

NEOFLON PCTFE M-400H is a high hardness fluororesin with excellent gas barrier properties. Introduction - NEOFLON PCTFE M-400H is a polymer with a structure in which all hydrogen atoms of polyvinyl chloride (CH 2 --CHCl) n are substituted with fluorine atoms. It is in the form of one chlorine atom in PTFE structural unit. - Highly transparent due to this chlorine atom. - It is a fluororesin with the highest gas barrier property and high hardness. - Excellent in mechanical properties, although it is slightly inferior to PFA and FEP in heat resistance and chemical resistance. - M-400H is a granular material with a higher molecular weight than M-300H. - It is excellent in stress crack resistance, suitable for compression molding.

NEOFLON PFA AF - 0012 is a fluoropolymer film with about the same characteristics as PTFE. Introduction - NEOFLON PFA film is smooth high-performing non-stretch film which is formed by melt extrusion with NEOFLON PFA material. - NEOFLON PFA film has a molecular structure in which a principle chain consisting of atoms of carbon and fluorine is combined with the perfluoroalkoxyl group, to give outstanding heat and chemical resistance, nonadhesion, and nonflammability. - It also possesses fabricating characteristics including sealing, thermoforming, welding and heat bonding as well as adhesion (surface treatment items).

NEOFLON PFA AF - 0025 is a fluoropolymer film with about the same characteristics as PTFE. Introduction - NEOFLON PFA film is smooth high-performing non-stretch film which is formed by melt extrusion with NEOFLON PFA material. - NEOFLON PFA film has a molecular structure in which a principle chain consisting of atoms of carbon and fluorine is combined with the perfluoroalkoxyl group, to give outstanding heat and chemical resistance, nonadhesion, and nonflammability. - It also possesses fabricating characteristics including sealing, thermoforming, welding and heat bonding as well as adhesion (surface treatment items).

NEOFLON PFA AF - 0025B1 is a fluoropolymer film with about the same characteristics as PTFE. Introduction - NEOFLON PFA film is smooth high-performing non-stretch film which is formed by melt extrusion with NEOFLON PFA material. - NEOFLON PFA film has a molecular structure in which a principle chain consisting of atoms of carbon and fluorine is combined with the perfluoroalkoxyl group, to give outstanding heat and chemical resistance, nonadhesion, and nonflammability. - It also possesses fabricating characteristics including sealing, thermoforming, welding and heat bonding as well as adhesion (surface treatment items). - By special surface treatment, it is possible to adhere to other materials such as adhesives, resins, rubbers etc, that were difficult in the past

NEOFLON PFA AF - 0050 is a fluoropolymer film with about the same characteristics as PTFE. Introduction - NEOFLON PFA film is smooth high-performing non-stretch film which is formed by melt extrusion with NEOFLON PFA material. - NEOFLON PFA film has a molecular structure in which a principle chain consisting of atoms of carbon and fluorine is combined with the perfluoroalkoxyl group, to give outstanding heat and chemical resistance, nonadhesion, and nonflammability. - It also possesses fabricating characteristics including sealing, thermoforming, welding and heat bonding as well as adhesion (surface treatment items).

NEOFLON PFA AF - 0050B1 is a fluoropolymer film with about the same characteristics as PTFE. Introduction - NEOFLON PFA film is smooth high-performing non-stretch film which is formed by melt extrusion with NEOFLON PFA material. - NEOFLON PFA film has a molecular structure in which a principle chain consisting of atoms of carbon and fluorine is combined with the perfluoroalkoxyl group, to give outstanding heat and chemical resistance, nonadhesion, and nonflammability. - It also possesses fabricating characteristics including sealing, thermoforming, welding and heat bonding as well as adhesion (surface treatment items). - By special surface treatment, it is possible to adhere to other materials such as adhesives, resins, rubbers etc, that were difficult in the past

NEOFLON PFA AF - 0100 is a fluoropolymer film with about the same characteristics as PTFE. Introduction - NEOFLON PFA film is smooth high-performing non-stretch film which is formed by melt extrusion with NEOFLON PFA material. - NEOFLON PFA film has a molecular structure in which a principle chain consisting of atoms of carbon and fluorine is combined with the perfluoroalkoxyl group, to give outstanding heat and chemical resistance, nonadhesion, and nonflammability. - It also possesses fabricating characteristics including sealing, thermoforming, welding and heat bonding as well as adhesion (surface treatment items).

NEOFLON PFA AF - 0100B1 is a fluoropolymer film with about the same characteristics as PTFE. Introduction - NEOFLON PFA film is smooth high-performing non-stretch film which is formed by melt extrusion with NEOFLON PFA material. - NEOFLON PFA film has a molecular structure in which a principle chain consisting of atoms of carbon and fluorine is combined with the perfluoroalkoxyl group, to give outstanding heat and chemical resistance, nonadhesion, and nonflammability. - It also possesses fabricating characteristics including sealing, thermoforming, welding and heat bonding as well as adhesion (surface treatment items). - By special surface treatment, it is possible to adhere to other materials such as adhesives, resins, rubbers etc, that were difficult in the past

NEOFLON PFA AF - 0250 is a fluoropolymer film with about the same characteristics as PTFE. Introduction - NEOFLON PFA film is smooth high-performing non-stretch film which is formed by melt extrusion with NEOFLON PFA material. - NEOFLON PFA film has a molecular structure in which a principle chain consisting of atoms of carbon and fluorine is combined with the perfluoroalkoxyl group, to give outstanding heat and chemical resistance, nonadhesion, and nonflammability. - It also possesses fabricating characteristics including sealing, thermoforming, welding and heat bonding as well as adhesion (surface treatment items).

NEOFLON PFA AF - 0500 is a fluoropolymer film with about the same characteristics as PTFE. Introduction - NEOFLON PFA film is smooth high-performing non-stretch film which is formed by melt extrusion with NEOFLON PFA material. - NEOFLON PFA film has a molecular structure in which a principle chain consisting of atoms of carbon and fluorine is combined with the perfluoroalkoxyl group, to give outstanding heat and chemical resistance, nonadhesion, and nonflammability. - It also possesses fabricating characteristics including sealing, thermoforming, welding and heat bonding as well as adhesion (surface treatment items).

NEOFLON PFA AF - 1000 is a fluoropolymer film with about the same characteristics as PTFE. Introduction - NEOFLON PFA film is smooth high-performing non-stretch film which is formed by melt extrusion with NEOFLON PFA material. - NEOFLON PFA film has a molecular structure in which a principle chain consisting of atoms of carbon and fluorine is combined with the perfluoroalkoxyl group, to give outstanding heat and chemical resistance, nonadhesion, and nonflammability. - It also possesses fabricating characteristics including sealing, thermoforming, welding and heat bonding as well as adhesion (surface treatment items).

NEOFLON PFA AF - 2400 is a fluoropolymer film with about the same characteristics as PTFE. Introduction - NEOFLON PFA film is smooth high-performing non-stretch film which is formed by melt extrusion with NEOFLON PFA material. - NEOFLON PFA film has a molecular structure in which a principle chain consisting of atoms of carbon and fluorine is combined with the perfluoroalkoxyl group, to give outstanding heat and chemical resistance, nonadhesion, and nonflammability. - It also possesses fabricating characteristics including sealing, thermoforming, welding and heat bonding as well as adhesion (surface treatment items).

NEOFLON PFA AF - 3000 is a fluoropolymer film with about the same characteristics as PTFE. Introduction - NEOFLON PFA film is smooth high-performing non-stretch film which is formed by melt extrusion with NEOFLON PFA material. - NEOFLON PFA film has a molecular structure in which a principle chain consisting of atoms of carbon and fluorine is combined with the perfluoroalkoxyl group, to give outstanding heat and chemical resistance, nonadhesion, and nonflammability. - It also possesses fabricating characteristics including sealing, thermoforming, welding and heat bonding as well as adhesion (surface treatment items).

NEOFLON PFA AP-201 is a high flowability fluororesin. It is suitable for injection molding of complicated shape products and extrusion molding of thin wall electric wire. Introduction - AP-201 is a copolymer of tetrafluoroethylene and perfluoroalkyl vinyl ether. - Good melt flowability while maintaining excellent properties of PTFE. It can be melt-molded as a thermoplastic resin by injection molding and extrusion molding. - Suitable for injection molding of complicated shape products and extrusion molding of thin-walled electric wires. - Excellent chemical resistance which is not affected by most of the chemicals. - It retains flexibility without losing toughness under the environment from cryogenic to high temperature. - Low dielectric constant and dielectric loss tangent in a wide range of temperature and frequency. - It shows high electrical resistance and dielectric strength. - Nonflammable like POLYFLON PTFE and NEOFLON FEP. - Excellent weather resistance. No properties change even when exposed outside for a long time. - Non-stickiness. It shows excellent releasability and water repellency / oil repellency.

NEOFLON PFA AP-201SH is a highly flowable and fully fluorinated resin. It is suitable for injection molding of complicated shape products and extrusion molding of thin wall electric wire. Introduction - AP-201SH is a copolymer of tetrafluoroethylene and perfluoroalkylvinylether. - High purity PFA with terminal groups fully fluorinated. - Good melt flowability while maintaining excellent properties of PTFE. It can be melt-molded as a thermoplastic resin by injection molding and extrusion molding. - Suitable for injection molding of complicated shaped products and extrusion molding of thin-walled electric wires. It is used for small parts of a semiconductor. - Less fluoride ions due to the fluorinated terminal group. - Excellent chemical resistance which is not affected by most of the chemicals. - It retains flexibility without losing toughness under the environment from cryogenic to high temperature. - Low dielectric constant and dielectric loss tangent in a wide range of temperature and frequency. - It shows high electrical resistance and dielectric strength. - Nonflammable like POLYFLON PTFE and NEOFLON FEP. - Excellent weather resistance. No properties change even when exposed outside for a long time. - Non-stickiness. It shows excellent releasability and water repellency / oil repellency.

NEOFLON PFA AP-202 is an ultra-high flowability fluororesin. It is suitable for extrusion molding of fine and thin wall electric wire Introduction - AP-202 is a copolymer of tetrafluoroethylene and perfluoroalkyl vinyl ether. - Good melt flowability while maintaining excellent properties of PTFE. It can be melt-molded as a thermoplastic resin by injection molding and extrusion molding. - Suitable for extrusion molding of extremely fine electric wires. It is also used for electric wires of personal computers and mobile phones. - Excellent chemical resistance which is not affected by most of the chemicals. - It retains flexibility without losing toughness under the environment from cryogenic to high temperature. - Low dielectric constant and dielectric loss tangent in a wide range of temperature and frequency. - It shows high electrical resistance and dielectric strength. - Nonflammable like POLYFLON PTFE and NEOFLON FEP. outside for a long time. - Non-stickiness. It shows excellent releasability and water repellency / oil repellency.

NEOFLON PFA AP-210 is excellent in melt flowability and is suitable for injection molding and extrusion molding. Introduction - AP-210 is a copolymer of tetrafluoroethylene and perfluoroalkyl vinyl ether. - Good melt flowability while maintaining excellent properties of PTFE. It can be melt-molded as a thermoplastic resin by injection molding and extrusion molding. - Excellent chemical resistance which is not affected by most of the chemicals. - Excellent heat resistance. Continuous use temperature is 260°C. - It retains flexibility without losing toughness under the environment from cryogenic to high temperature. - Low dielectric constant and dielectric loss tangent in a wide range of temperature and frequency. - It shows high electrical resistance and dielectric strength. - Nonflammable like POLYFLON PTFE and NEOFLON FEP. - Excellent weather resistance. No properties change even when exposed outside for a long time. - Non-stickiness. It shows excellent releasability and water repellency / oil repellency.

NEOFLON PFA AP-211SH is a fully fluorinated high purity PFA. Melt flowability and stress crack resistance are excellent. It is suitable for injection molded parts used for semiconductors. Introduction - AP-211SH is a copolymer of tetrafluoroethylene and perfluoro alkyl vinyl ether. At the same time, it is a high purity PFA with its end groups completely fluorinated. - Good melt flowability while maintaining excellent properties of PTFE. It can be used for melt molding as a thermoplastic resin. Injection molding and extrusion molding are suitable. - Excellent in melt flowability. Applicable for injection molded products. It has been used for injection molded parts for semiconductors such as fitting nuts. - Less eluted fluoride ions. Due to the fluorinated terminal group. - The most excellent stress crack resistance in injection molding grade of PFA. - Excellent chemical resistance which is not affected by most of the chemicals. - Flexible and tough under the cryogenic to high temperature. - Excellent heat resistance. Continuous use temperature is 260°C. - Nonflammable like POLYFLON PTFE and NEOFLON FEP. - Excellent weather resistance. No properties change even when exposed outside for a long time.

NEOFLON PFA AP-221SH is fully fluorinated fluororesin with improved crack resistance while maintaining melt flowability. Introduction - AP-221SH is a copolymer of tetrafluoroethylene and perfluoroalkyl vinyl ether. It is PFA with its end groups completely fluorinated. - Good melt flowability while maintaining excellent properties of PTFE. It can be used for melt molding as a thermoplastic resin. Transfer molding and extrusion molding are suitable. - Excellent in stress crack resistance, - Especially suitable for transfer molded products. It has been used for small size valve lining applications. - Less eluted fluoride ions. Due to the fluorinated terminal group. - Excellent chemical resistance which is not affected by most of the chemicals. - It retains flexibility without losing toughness under the environment from cryogenic to high temperature, - Excellent heat resistance. Continuous use temperature is 260°C. - Low dielectric constant and dielectric loss tangent in a wide range of temperature and frequency. - Nonflammable like POLYFLON PTFE and NEOFLON FEP. - Excellent weather resistance. No properties change even when exposed outside for a long time.

NEOFLON PFA AP-230 is a fluororesin that is excellent in melt flowability. It is suitable for extrusion molding. Introduction - AP-230 is a copolymer of tetrafluoroethylene and perfluoroalkyl vinyl ether. - Good melt flowability while maintaining excellent properties of PTFE. It can be melt-molded as a thermoplastic resin by extrusion molding, transfer molding, compression molding and the like. - It has been used for tubes, pipes, sheets, lining applications. - It is widely used as a thick plate material by compression molding. - Excellent chemical resistance which is not affected by most of the chemicals. - It retains flexibility without losing toughness under the environment from cryogenic to high temperature. - Excellent heat resistance. Continuous use temperature is 260°C. - Low dielectric constant and dielectric loss tangent in a wide range of temperature and frequency. - It shows high electrical resistance and dielectric strength. - Nonflammable like POLYFLON PTFE and NEOFLON FEP. - Excellent weather resistance. No properties change even when exposed outside for a long time. - Non-stickiness. It shows excellent releasability and water repellency / oil repellency.

NEOFLON PFA AP-230AS is a conductive fluorocarbon resin. It is suitable for extrusion molding. Introduction - AP-230AS is a copolymer of tetrafluoroethylene and perfluoroalkyl vinyl ether. - It is a PFA with conductivity. - Good melt flowability while maintaining excellent properties of PTFE. It can be melt-molded as a thermoplastic resin by extrusion molding, transfer molding, compression molding and the like. - Especially, it is used for thin-walled tubes for copy rolls by extrusion molding. - Excellent chemical resistance which is not affected by most of the chemicals. - It can also be adopted to conductive valve lining applications. - It retains flexibility without losing toughness under the environment from cryogenic to high temperature. - No change in the resistance value up to 200°C. - Non-stickiness. It shows excellent releasability and water repellency / oil repellency.

NEOFLON PFA AP-230ASL is a conductive fluorocarbon resin. It is suitable for extrusion molding. Introduction - AP-230 ASL is a conductive fluorocarbon resin suitable for extrusion molding. - It is a PFA with conductivity. - Good melt flowability while maintaining excellent properties of PTFE. It can be melt-molded as a thermoplastic resin by extrusion molding, transfer molding, compression molding and the like. - Especially, it is used for thin-walled tubes for copy rolls by extrusion molding. - Excellent chemical resistance which is not affected by most of the chemicals. - It can also be adopted to conductive valve lining applications. - It retains flexibility without losing toughness under the environment from cryogenic to high temperature. - No change in the resistance value up to 200°C. - Non-stickiness. It shows excellent releasability and water repellency / oil repellency.

NEOFLON PFA AP-230SH is a high purity PFA with fully fluorinated. It is excellent in melt flowability. It is suitable for chemical liquid tubes of semiconductors by extrusion molding. Introduction AP-230SH is a copolymer of tetrafluoroethylene and perfluoroalkylvinylether. - High purity PFA with terminal groups fully fluorinated. - Good melt flowability while maintaining excellent properties of PTFE. It can be melt-molded as a thermoplastic resin by extrusion molding. - Suitable for extrusion molding and transfer molding. It is used for tubes, sheets and valve lining applications. - Less fluoride ions due to the fluorinated terminal group. - Excellent chemical resistance which is not affected by most of the chemicals. - It retains flexibility without losing toughness under the environment from cryogenic to high temperature. - Excellent heat resistance. Continuous use temperature is 260°C. - Excellent weather resistance. No properties change even when exposed outside for a long time. - Non-stickiness. It shows excellent releasability and water repellency / oil repellency.

NEOFLON PFA AP-231SH is a high purity PFA with fully fluorinated. It is excellent in melt processability and stress crack resistance. It is used for chemical supply tubing at semiconductor factories. Introduction - AP-231SH is a copolymer of tetrafluoroethylene and perfluoroalkylvinylether. - High purity PFA with terminal groups fully fluorinated. - Good melt flowability while maintaining excellent properties of PTFE. It can be melt-molded as a thermoplastic resin by extrusion molding. - Suitable for extrusion molding and transfer molding. It is used for tubes, sheets and valve lining applications. - Less fluoride ions due to the fluorinated terminal group. - It is a PFA with the best stress crack resistance. - Excellent chemical resistance which is not affected by most of the chemicals. - It retains flexibility without losing toughness under the environment from cryogenic to high temperature. - Excellent heat resistance. Continuous use temperature is 260°C. - Excellent weather resistance. No properties change even when exposed outside for a long time. - Non-stickiness. It shows excellent releasability and water repellency / oil repellency.