TECNOFLON® FOR 9383 is a medium-high viscosity cure incorporated fluoroelastomer terpolymer (FKM) with 68.5% fluorine content. Tecnoflon® FOR 9383 is well suited for all applications requiring better chemical resistance and/or long term heat resistance compared to fluoroelastomer copolymers and in any application requiring adhesion to metal. Tecnoflon® FOR 9383 contains proprietary cure system providing superior processability for fast cycles and scorch safety. Some of the basic properties of TECNOFLON® FOR 9383 are: - Very good processability - Excellent chemical resistance - Good hot tear resistance - Good heat resistance - Good bonding to metal - Very good scorch safety Tecnoflon® FOR 9383 can be used for compression, injection and transfer moulding of shaft seals, valve stem seals, gaskets or any item requiring excellent chemical resistance. This material can be combined with the cure system and other typical fluoroelastomer compounding ingredients. Mixing can be accomplished with two-roll mills or internal mixers. Tecnoflon® FOR 9383 can be extruded into hoses or profiles and can be calendered to make sheet stocks or belting. Finished goods can be produced by a variety of rubber processing methods.

TECNOFLON® FOR 9385F is a medium viscosity cure incorporated fluoroelastomer terpolymer (FKM) with 68.5 % fluorine content. Tecnoflon® FOR 9385F is designed to improve bonding in any application requiring adhesion to metal. In shaft seals or valve stem seals production, Tecnoflon® FOR 9385F greatly reduces the reject rate due to adhesion and molding problems. Some of the basic properties of Tecnoflon® FOR 9385F are: - Superior bonding to metal - Very good scorch safety - Outstanding processability - Lack of mold fouling - Excellent hot tear resistance - Excellent mold release Tecnoflon® FOR 9385F can be used for compression, injection and transfer molding of shaft seals, valve stem seals, O-rings, gaskets and seals. This material can be extruded into hoses or profiles and can be calendered to make sheet stocks or belting. Tecnoflon® FOR 9385F can be combined with the cure system and other typical fluoroelastomer compounding ingredients. Mixing can be accomplished with two-roll mills or internal mixers.

TECNOFLON® FOR TF 636 is a medium-low viscosity cure incorporated fluoroelastomer terpolymer designed to provide improved low temperature characteristics. Tecnoflon® FOR TF 636 exhibits the same excellent heat and chemical resistance expected from Tecnoflon® copolymers. Some of the basic properties of TECNOFLON® FOR TF 636 are: - Improved low temperature performance - Good heat and chemical resistance - Very low compression set - Excellent mould release - Lack of mould fouling - Superior mould flow Tecnoflon ® FOR TF 636 can be used for compression, injection and transfer molding of O-rings, diaphragms, gaskets, seals, moulded shapes or other items requiring improved low temperature performance. Tecnoflon ® FOR TF 636 can be combined with the cure system and other typical fluoroelastomer compounding ingredients. Mixing can be accomplished with two roll mills or internal mixers. Tecnoflon ® FOR TF 636 can be extruded into hoses or profiles and can be calendered to make sheet stocks or belting. Finished goods can be produced by a variety of rubber processing methods. Handling and safety - Normal care and precautions should be taken to avoid skin contact, eye contact and breathing of fumes. Smoking is prohibited in working areas. Wash hands before eating or smoking. For complete health and safety information, please refer to the material safety data sheet.

TECNOFLON® FOR TF 838K is a medium viscosity cure incorporated fluoroelastomer terpolymer (FKM) with 68 % fluorine content. Tecnoflon® FOR TF 838K is designed to improve bonding in any application requiring adhesion to metal. In shaft seals or valve stem seals production, Tecnoflon® FOR TF 838K greatly reduces the reject rate due to adhesion and molding problems. Tecnoflon® FOR TF 838K shows low crosslinking density, in order to allow further addition of curatives. Some of the basic properties of Tecnoflon® FOR TF 838K are: - Superior bonding to metal - Very good scorch safety - Outstanding processability - Lack of mold fouling - Excellent hot tear resistance - Excellent mold release Tecnoflon® FOR TF 838K can be used for compression, injection and transfer molding of shaft seals, valve stem seals, O-rings, gaskets and seals. Tecnoflon® FOR TF 838K can be combined with the cure system and other typical fluoroelastomer compounding ingredients. Mixing can be accomplished with two-roll mills or internal mixers. This material can be extruded into hoses or profiles and can be calendered to make sheet stocks or belting. Finished goods can be produced by a variety of rubber processing methods.

TECNOFLON® FOR TF is a high viscosity cure incorporated fluoroelastomer terpolymer (FKM) with 68% fluorine content. Tecnoflon® FOR TF is well suited for applications requiring better chemical resistance and/or long term heat resistance compared to fluoroelastomer copolymers. Some of the basic properties of Tecnoflon® FOR TF are: - Excellent chemical resistance - Good compression set - Excellent mould release - Lack of mould fouling - Superior mould flow Tecnoflon® FOR TF can be used for compression and transfer moulding of seals, gaskets or any item requiring excellent chemical resistance. This material can be combined with the cure system and other typical fluoroelastomer compounding ingredients. Mixing can be accomplished with two-roll mills or internal mixers. Tecnoflon® FOR TF can be extruded into hoses or profiles and can be calendered to make sheet stocks or belting. Finished goods can be produced by a variety of rubber processing methods.

TECNOFLON® L 636 is a medium-low viscosity fluoroelastomer terpolymer with 66% fluorine content, designed to provide improved low temperature characteristics. Tecnoflon® L 636 does not contain curatives: therefore the proper levels of Tecnoflon® FOR M1 and Tecnoflon® FOR M2 must be added to achieve the required properties. Tecnoflon® L 636 is especially suited for injection moulding of O-rings and sealing components which must meet demanding specifications. Tecnoflon® L 636 exhibits the same excellent heat and chemical resistance expected from Tecnoflon® copolymers. Some of the basic properties of TECNOFLON® L 636 are: - Improved low temperature performance - Good heat and chemical resistance - Very low compression set - Excellent mould release - Lack of mould fouling - Superior mould flow Tecnoflon® L 636 can be used for compression, injection and transfer molding of O-rings, diaphragms, gaskets, seals, moulded shapes or other items requiring improved low temperature performance. Tecnoflon® L 636 can be combined with the cure system and other typical fluoroelastomer compounding ingredients. Mixing can be accomplished with two-roll mills or internal mixers. This material can be extruded into hoses or profiles and can be calendered to make sheet stocks or belting. Finished goods can be produced by a variety of rubber processing methods.

Tecnoflon® N 215 is a very low viscosity fluoroelastomer copolymer. Tecnoflon® N 215 is intended for blending with other polymers of the Tecnoflon® family to achieve the desired viscosity. It is also intended for high concentration solution applications, such as dip coated items, fabric coatings and spray coating. Tecnoflon® N 215 can be mixed in the same way as all the other Tecnoflon® grades and can be used in any application requiring either very low compound viscosity or "low viscosity", highly loaded high hardness compounds. Tecnoflon® N 215 does not contain curatives: therefore the proper levels of Tecnoflon® FOR M1 and Tecnoflon® FOR M2 must be added to achieve the required properties. It can be also cured with diamine based systems such as Tecnoflon® Tecnocin A and Tecnoflon® Tecnocin B. Some of the unique properties of Tecnoflon® N 215 are: - Solution applications -- Excellent pot life -- Very low Brookfield viscosity -- Excellent adhesion to substrates - Dry applications -- Superior mould flow -- Low compound viscosity -- Good compression set Tecnoflon® N 215 can be mixed using typical fluoroelastomers compounding ingredients and mixing can be accomplished with two-roll mills or internal mixers. Compounds based on Tecnoflon® N 215 can be dispersed in solvents for coating applications. Finished goods can be produced by a variety of rubber processing methods.

Tecnoflon® N 535 is a low viscosity fluoroelastomer copolymer. Tecnoflon® N 535 is intended as a general purpose fluoroelastomer. It can be blended with other polymers of the Tecnoflon® family to meet specific requirements. Tecnoflon® N 535 does not contain curatives: therefore the proper levels of Tecnoflon® FOR M1 and Tecnoflon® FOR M2 must be added to achieve the required properties. It can be also cured with diamine based systems such as Tecnoflon® Tecnocin A and Tecnoflon® Tecnocin B. Some of the unique properties of Tecnoflon® N 535 are: - Excellent compression set - Lack of mould fouling - Superior extrusion behaviour - Superior mould flow - Excellent mould release Tecnoflon® N 535 can be used for injection and transfer moulding of O-rings, gaskets and seals. The product can be mixed using typical fluoroelastomers compounding ingredients and mixing can be accomplished with two-roll mills or internal mixers. The material can be extruded into hoses or profiles and can be calendered to make sheet stocks or belting. Compounds based on Tecnoflon® N 535 can be dispersed in solvents for coating applications. Finished goods can be produced by a variety of rubber processing methods.

Tecnoflon® N 935 is a medium high viscosity fluoroelastomer copolymer. Tecnoflon® N 935 is intended as a general purpose fluoroelastomer. It can be blended with other polymers of the Tecnoflon® family to meet specific requirements. Tecnoflon® N 935 does not contain curatives: therefore the proper levels of Tecnoflon® FOR M1 and Tecnoflon® FOR M2 must be added to achieve the required properties. It can be also cured with diamine based systems such as Tecnoflon® Tecnocin A and Tecnoflon® Tecnocin B. Some of the unique properties of Tecnoflon® N 935 are: - Excellent compression set - Lack of mould fouling - Superior extrusion behaviour - Superior mould flow - Excellent mould release - Compliant to FDA 21,CFR 177.2600 Tecnoflon® N 935 can be used for compression moulding of O-rings, seals, gaskets and other items. The product can be mixed using typical fluoroelastomers compounding ingredients and mixing can be accomplished with two-roll mills or internal mixers. The material can be extruded into hoses or profiles and can be calendered to make sheet stocks or belting. Compounds based on Tecnoflon® N 935 can be dispersed in solvents for coating applications. Finished goods can be produced by a variety of rubber processing methods.

TECNOFLON® NH is a high viscosity fluoroelastomer copolymer. Tecnoflon® NH is intended as a general purpose fluoroelastomer. It can be blended with other polymers of the Tecnoflon® family to meet specific requirements. Tecnoflon® NH does not contain curatives: therefore the proper levels of Tecnoflon® FOR M1 and Tecnoflon® FOR M2 must be added to achieve the required properties. It can be also cured with diamine based systems such as Tecnoflon® Tecnocin A and Tecnoflon® Tecnocin B. Some of the unique properties of TECNOFLON® NH are: - Excellent compression set - Lack of mould fouling - Excellent mould release TECNOFLON® NH can be used for compression moulding of O-rings, seals, gaskets and other items. The product can be mixed using typical fluoroelastomers compounding ingredients and mixing can be accomplished with two-roll mills or internal mixers. Finished goods can be produced by a variety of rubber processing methods.

TECNOFLON® P 457 is a low viscosity, medium fluorine (67%), peroxide curable fluoroelastomer. Tecnoflon® P 457 exhibits superior resistance to a wide variety of chemicals, coupled with excellent processability, optimum compression set and good flexibility at low temperatures. Tecnoflon® P 457 can be cross-linked using organic peroxides in conjunction with a coagent. Tecnoflon® P 457 is a lower viscosity version of Tecnoflon® P 757: please refer to Tecnoflon® P 757 Technical data sheet for data on chemical resistance. Some of the basic properties of TECNOFLON® P 457 are: - Low post cure - Superior mold flow - Lack of mold fouling - Excellent mold release - Good chemical resistance - Good stress relaxation - Good metal bonding - Good low temperature performance Tecnoflon® P 457 can be used for injection and transfer molding of shaft seals, valve seals, Orings, gaskets or any item requiring superior chemical resistance. Tecnoflon® P 457 can be combined with the cure system and other typical fluoroelastomer compounding ingredients. Mixing can be accomplished with two-roll mills or internal mixers. This material can be extruded into hoses or profiles and can be calendered to make sheet stocks or belting. Finished goods may be produced by a variety of rubber processing methods.

TECNOFLON® P 459 is a low viscosity, high fluorine (70%), peroxide curable fluoroelastomer. Tecnoflon® P 459 exhibits superior resistance to a wide variety of chemicals, coupled with excellent processability and optimum compression set. Tecnoflon® P 459 can be cross-linked using organic peroxides in conjunction with a co-agent. Tecnoflon® P 459 is a lower viscosity version of Tecnoflon® P 959: please refer to Tecnoflon® P 959 Technical data sheet for data on chemical resistance. Some of the basic properties of TECNOFLON® P 459 are: - Low post cure - Superior mold flow - Lack of mold fouling - Excellent mold release - Good chemical resistance especially in: -- Alcohol containing fuels -- Steam -- Fluids containing amine additives Tecnoflon® P 459 can be used for injection and transfer molding of shaft seals, valve seals, Orings, gaskets or any item requiring superior chemical resistance. Tecnoflon® P 459 can be combined with the cure system and other typical fluoroelastomer compounding ingredients. Mixing can be accomplished with two-roll mills or internal mixers. Finished goods may be produced by a variety of rubber processing methods. This material can be extruded into hoses or profiles and can be calendered to make sheet stocks or belting.

TECNOFLON® P 757 is a medium viscosity, medium fluorine (67%), peroxide curable fluoroelastomer. Tecnoflon® P 757 exhibits superior resistance to a wide variety of chemicals, coupled with excellent processability, optimum compression set and good flexibility at low temperatures. Tecnoflon® P 757 can be cross-linked using organic peroxides in conjunction with a coagent. Some of the basic properties of TECNOFLON® P 757 are: - Low post cure - Superior mold flow - Lack of mold fouling - Excellent mold release - Good chemical resistance - Good stress relaxation - Good metal bonding - Good low temperature performance Tecnoflon® P 757 can be used for compression, injection and transfer molding of shaft seals, valve seals, O-rings, gaskets or any item requiring superior chemical resistance. Tecnoflon® P 757 can be combined with the cure system and other typical fluoroelastomer compounding ingredients. Mixing can be accomplished with two-roll mills or internal mixers. This material can be extruded into hoses or profiles and can be calendered to make sheet stocks or belting. Finished goods may be produced by a variety of rubber processing methods.

TECNOFLON® P 959 is a medium viscosity, high fluorine (70%), peroxide curable fluoroelastomer. Tecnoflon® P 959 exhibits superior resistance to a wide variety of chemicals, coupled with excellent processability and optimum compression set. Tecnoflon® P 959 can be cross-linked using organic peroxides in conjunction with a co-agent. Some of the basic properties of TECNOFLON® P 959 are: - Low post cure - Superior mold flow - Lack of mold fouling - Excellent mold release - Good chemical resistance especially in: -- Alcohol containing fuels -- Steam -- Fluids containing amine additives Tecnoflon® P 959 can be used for compression, injection and transfer molding of shaft seals, valve seals, O-rings, gaskets or any item requiring superior chemical resistance. Tecnoflon® P 959 can be combined with the cure system and other typical fluoroelastomer compounding ingredients. Mixing can be accomplished with two-roll mills or internal mixers. Finished goods may be produced by a variety of rubber processing methods.This material can be extruded into hoses or profiles and can be calendered to make sheet stocks or belting.

TECNOFLON® PL 455 is a new generation low temperature peroxide curable low viscosity fluoroelastomer with 64% wt fluorine content. Tecnoflon® PL 455 exhibits excellent low temperature flexibility (TR10 = -30°C). Like all other Tecnoflon® peroxide curable grades, it exhibits excellent processability; moreover it needs very short post-curing cycles. Some of the basic properties of Tecnoflon® PL 455 are: - Excellent low temperature flexibility - Low post cure - Superior mold flow - Lack of mold fouling - Excellent mold release Tecnoflon® PL 455 can be used for injection, injection-compression and transfer molding of O-rings, gaskets and seals. Tecnoflon® PL 455 can be combined with the cure system and other typical fluoroelastomer compounding ingredients. Mixing can be accomplished with two-roll mills or internal mixers. This material can be extruded into hoses or profiles and can be calendered to make sheet stocks or belting. Finished goods may be produced by a variety of rubber processing methods.

Tecnoflon® PL 458 is a new generation low post cure peroxide curable fluoroelastomer. Tecnoflon® PL 458 exhibits both excellent low temperature flexibility (TR10 = -24°C) and outstanding resistance to a variety of chemicals. As all other Tecnoflon® peroxide curable grades, it exhibits excellent processability; moreover it needs very short post-curing cycles. Some of the basic properties of Tecnoflon® PL 458 are: - Excellent low temperature flexibility - Low volume swell in methanol-based fuels - Low post cure - Superior mould flow - Lack of mould fouling - Excellent mould release Tecnoflon® PL 458 can be used for injection, compression and transfer molding of O-rings, gaskets and seals. Tecnoflon® PL 458 can be combined with the cure system and other typical fluoroelastomer compounding ingredients. Mixing can be accomplished with two-roll mills or internal mixers. This material can be extruded into hoses or profiles and can be calendered to make sheet stocks or belting. Finished goods may be produced by a variety of rubber processing methods.

TECNOFLON® PL 557 is a new generation low temperature peroxide curable fluoroelastomer with 65.5% wt fluorine content. Tecnoflon® PL 557 exhibits excellent low temperature flexibility (TR10 = -29°C), close to Tecnoflon® PL 455, but with improved chemical resistance and permeability. Like all other Tecnoflon® peroxide curable grades, it exhibits excellent processability; moreover it needs very short post-curing cycles. Some of the basic properties of TECNOFLON® PL 557 are: - Excellent low temperature flexibility - Low post cure - Superior mold flow - Lack of mold fouling - Excellent mold release Tecnoflon® PL 557 can be used for injection, injection-compression and transfer molding of O-rings, gaskets and seals. This material can be extruded into hoses or profiles and can be calendered to make sheet stocks or belting. Tecnoflon® PL 557 can be combined with the cure system and other typical fluoroelastomer compounding ingredients. Mixing can be accomplished with two-roll mills or internal mixers.

TECNOFLON® PL 855 is a new generation low temperature peroxide curable medium viscosity fluoroelastomer with 64% wt fluorine content. Tecnoflon® PL 855 exhibits excellent low temperature flexibility (TR10 = -30°C). Like all other Tecnoflon® peroxide curable grades, it exhibits excellent processability; moreover it needs very short post-curing cycles. Some of the basic properties of Tecnoflon® PL 855 are: - Excellent low temperature flexibility - Low post cure - Superior mold flow - Lack of mold fouling - Excellent mold release Tecnoflon® PL 855 can be used for injection, injection-compression and transfer molding of O-rings, gaskets and seals. Tecnoflon® PL 855 can be combined with the cure system and other typical fluoroelastomer compounding ingredients. Mixing can be accomplished with two-roll mills or internal mixers. This material can be extruded into hoses or profiles and can be calendered to make sheet stocks or belting. Finished goods may be produced by a variety of rubber processing methods.

TECNOFLON® PL 958 is a new generation low post cure peroxide curable fluoroelastomer. Tecnoflon® PL 958 exhibits both excellent low temperature flexibility (TR10 = -24°C) and an outstanding resistance to a variety of chemicals. As all other Tecnoflon® peroxide curable grades, it exhibits excellent processability; moreover it needs very short post-curing cycles. Tecnoflon® PL 958 is a higher viscosity version of Tecnoflon® PL 458: please refer to Tecnoflon® PL 458 Technical data sheet for data on chemical resistance. Some of the basic properties of TECNOFLON® PL 958 are: - Excellent low temperature flexibility - Low volume swell in methanol-based fuels - Low post cure - Superior mould flow - Lack of mould fouling - Excellent mould release Tecnoflon® PL 958 can be used for compression, injection-compression and transfer molding of O-rings, gaskets and seals. Tecnoflon® PL 958 can be combined with the cure system and other typical fluoroelastomer compounding ingredients. Mixing can be accomplished with two-roll mills or internal mixers. This material can be extruded into hoses or profiles and can be calendered to make sheet stocks or belting. Finished goods may be produced by a variety of rubber processing methods.

TECNOFLON® T 538 is a low viscosity fluoroelastomer terpolymer with 68.5% fluorine content. Tecnoflon® T 538 has been designed and synthesized with a new patented polymerization technology that assures improved processability and outstanding physical properties. Tecnoflon® T 538 does not contain curatives: therefore the proper levels of Tecnoflon® FOR M1 and Tecnoflon® FOR M2 must be added to achieve the required properties. Tecnoflon® T 538 exhibits the chemical resistance typical of fluoroelastomer terpolymers. It is well suited for applications requiring better chemical resistance and/or long term heat resistance compared to fluoroelastomer copolymers. Some of the basic properties of Tecnoflon® T 538 are: - Excellent chemical resistance - Good heat resistance - Excellent processability Tecnoflon® T 538 can be used for compression, injection and transfer molding of shaft seals, valve stem seals, gaskets or any item requiring excellent chemical resistance This material can be combined with the cure system and other typical fluoroelastomer compounding ingredients. Mixing can be accomplished with two-roll mills or internal mixers. Tecnoflon® T 538 can be extruded into hoses or profiles and can be calendered to make sheet stocks or belting. Finished goods can be produced by a variety of rubber processing methods.

TECNOFLON® T 636/L is a low viscosity fluoroelastomer terpolymer designed to provide improved low temperature characteristics. Tecnoflon® T 636/L does not contain curatives: therefore the proper levels of Tecnoflon® FOR M1 and Tecnoflon® FOR M2 must be added to achieve the required properties. Tecnoflon® T 636/L is a lower viscosity version of Tecnoflon® T 636: please refer to Tecnoflon® T 636 Technical data sheet for data on chemical resistance: Tecnoflon® T 636/L exhibits the same excellent heat and chemical resistance expected from Tecnoflon® copolymers. Some of the basic properties of TECNOFLON® T 636/L are: - Improved low temperature performance - Good heat and chemical resistance - Very low compression set - Excellent mould release - Lack of mould fouling - Superior mould flow Tecnoflon® T 636/L can be used for compression, injection and transfer molding of O-rings, diaphragms, gaskets, seals, moulded shapes or other items requiring improved low temperature performance. Tecnoflon® T 636/L can be combined with the cure system and other typical fluoroelastomer compounding ingredients. Mixing can be accomplished with two-roll mills or internal mixers. This material can be extruded into hoses or profiles and can be calendered to make sheet stocks or belting. Finished goods can be produced by a variety of rubber processing methods.

TECNOFLON® T 636 is a medium-low viscosity fluoroelastomer terpolymer designed to provide improved low temperature characteristics. Tecnoflon® T 636 does not contain curatives: therefore the proper levels of Tecnoflon® FOR M1 and Tecnoflon® FOR M2 must be added to achieve the required properties. Tecnoflon® T 636 exhibits the same excellent heat and chemical resistance expected from Tecnoflon® copolymers. Some of the basic properties of TECNOFLON® T 636 are: - Improved low temperature performance - Good heat and chemical resistance - Very low compression set - Excellent mould release - Lack of mould fouling - Superior mould flow Tecnoflon® T 636 can be used for compression, injection and transfer molding of O-rings, diaphragms, gaskets, seals, moulded shapes or other items requiring improved low temperature performance. Tecnoflon® T 636 can be combined with the cure system and other typical fluoroelastomer compounding ingredients. Mixing can be accomplished with two-roll mills or internal mixers. This material can be extruded into hoses or profiles and can be calendered to make sheet stocks or belting. Finished goods can be produced by a variety of rubber processing methods.

TECNOFLON® T 938 is a medium viscosity fluoroelastomer terpolymer with 68.5% fluorine content. Tecnoflon® T 938 does not contain curatives: therefore the proper levels of Tecnoflon® FOR M1 and Tecnoflon® FOR M2 must be added to achieve the required properties. Tecnoflon® T 938 exhibits the chemical resistance typical of fluoroelastomer terpolymers. It is well suited for applications requiring better chemical resistance and/or long term heat resistance compared to fluoroelastomer copolymers. Some of the basic properties of TECNOFLON® T 938 are: - Excellent chemical resistance - Good heat resistance - Very good processability Tecnoflon® T 938 can be used for compression, injection and transfer molding of shaft seals, valve stem seals, gaskets or any item requiring excellent chemical resistance This material can be combined with the cure system and other typical fluoroelastomer compounding ingredients. Mixing can be accomplished with two-roll mills or internal mixers. Tecnoflon® T 938 can be extruded into hoses or profiles and can be calendered to make sheet stocks or belting. Finished goods can be produced by a variety of rubber processing methods.

TECNOFLON® TN 50A is a medium-low viscosity fluoroelastomer terpolymer. It does not contain curatives, therefore the proper levels of Tecnoflon® FOR M1 and Tecnoflon® FOR M2 must be added to achieve required properties. Thanks to its 68% of fluorine content, a good compromise between chemical resistance and compression set value is obtained. The careful distribution of molecular weights and medium-low viscosity maximize its performance in applications such as injection molding or extrusion where rheological properties are critical. Some of the basic properties of Tecnoflon® TN 50A are: - Very good mold flow - Superior mold release - Good compression set - Good extrusion behavior Tecnoflon® TN 50A can be used for compression, injection and transfer molding of shaft seals, valve stem seals, O-rings, gaskets and seals. This material can be combined with the cure system and other typical fluoroelastomer compounding ingredients. Mixing can be accomplished with two-roll mills or internal mixers. Tecnoflon® TN 50A can be extruded into hoses or profiles and can be calendered to make sheet stocks or belting. Finished goods can be produced by a variety of rubber processing methods.

TECNOFLON® TN is a high viscosity fluoroelastomer terpolymer. TN is well suited for applications requiring better chemical resistance and/or long term heat resistance compared to fluoroelastomer copolymers. It can be blended with other polymers of the Tecnoflon® family to meet specific requirements. TN does not contain curatives, therefore the proper levels of Tecnoflon® FOR M1 and Tecnoflon® FOR M2 must be added to achieve required properties. It can also be cured with diamines. Some of the basic properties of TECNOFLON® TN are: - Excellent chemical resistance - Good compression set - Excellent mould release - Lack of mould fouling - Superior mould flow Tecnoflon® TN can be used for compression and transfer molding of shaft seals, valve stem seals, O-rings, gaskets, seals or any item requiring excellent chemical resistance. Tecnoflon® TN can be combined with the cure system and other typical fluoroelastomer compounding ingredients. Mixing can be accomplished with two-roll mills or internal mixers. This material can be extruded into hoses or profiles and can be calendered to make sheet stocks or belting. Finished goods can be produced by a variety of rubber processing methods.

Tecnoflon® VPL 45535 is a brand new generation very low temperature peroxide curable fluoroelastomer with outstanding low temperature flexibility (TR10 = -35°C). Like all other Tecnoflon® peroxide curable grades, it exhibits excellent processability; moreover it needs very short post-curing cycles. Some of the basic properties of Tecnoflon® VPL 45535 are: - Outstanding low temperature flexibility - Excellent chemical resistance, especially in alcohol containing fuels - Low post cure - Superior mold flow - Lack of mold fouling - Excellent mold release Tecnoflon® VPL 45535 can be used for compression, injection, injection-compression and transfer molding of O-rings, gaskets and seals. Tecnoflon® VPL 45535 can be combined with the cure system and other typical fluoroelastomer compounding ingredients. Mixing can be accomplished with two-roll mills or internal mixers. This material can be extruded into hoses or profiles and can be calendered to make sheet stocks or belting. Finished goods may be produced by a variety of rubber processing methods.

Tecnoflon® VPL 85540 and 55540 belong to a brand new generation of very low temperature peroxide curable FKM. They have been designed to offer outstanding low temperature flexibility (i.e. TR10 = -40°C). Like all other Tecnoflon® peroxide curable grades, they exhibit excellent processability and superior mechanical properties and sealing ability; moreover they need very short post curing cycles. Some of the basic properties of Tecnoflon® VPL 85540 and 55540 are: - Outstanding low temperature behavior - Very good chemical resistance - Low post cure - Superior mold flow - Lack of mold fouling - Excellent mold release - Very good chemical resistance Syensqo offers medium (VPL 85540) and low viscosity (VPL 55540) versions in order to fulfil all customer's requirements. Accordingly to the curing technology, Tecnoflon® VPL 85540 and VPL 55540 can be transformed by all the molding techniques, including injection, injection-compression, compression and transfer molding. Tecnoflon® VPL 85540 and 55540 can be used with all typical peroxide curing system and the other fluoroelastomer compounding ingredients. Mixing can be accomplished with two-roll mills or internal mixers. This material can be extruded into hoses or profiles or can be calendered to make sheet stocks or belting.

Tecnoflon® VPL 85730 and VPL 45730 are a brand new generation of very low temperature peroxide curable fluoroelastomer with outstanding low temperature flexibility (TR10 = -30°C). Furthermore, they show an improved chemical resistance if compared to Tecnoflon® PL grades with similar TR10. Like all other Tecnoflon® peroxide curable grades, they exhibit excellent processability; moreover they need very short post-curing cycles. Some of the basic properties of Tecnoflon® VPL 85730 and VPL 45730 are: - Outstanding low temperature flexibility - Excellent chemical resistance - Low post cure - Superior mold flow - Lack of mold fouling - Excellent mold release Tecnoflon® VPL 85730 and VPL 45730 can be used for compression, injection, injection-compression and transfer molding of Orings, gaskets and seals. Tecnoflon® VPL 85730 and VPL 45730 can be combined with the cure system and other typical fluoroelastomer compounding ingredients. Mixing can be accomplished with two-roll mills or internal mixers. These materials can be extruded into hoses or profiles and can be calendered to make sheet stocks or belting. Finished goods may be produced by a variety of rubber processing methods.