Biobased thermoplastic compound

Biobased thermoplastic compound

High Performance Polymer for Polypropylene Modification, based on hydrocarbon resin C5, with a softening point above 140°C.

MOISTURE CROSSLINKABLE MULTI-COMPONENT SYSTEM BASED ON GRAFTED XLPO POLYMER FOR LOW VOLTAGE WIRE APPLICATIONS (RoHS COMPLIANT) DESCRIPTION AquaGraft® 1-6010 is a moisture crosslinkable, natural, XLPO grafted polymer system that is composed of PEMC-1 grafted base polymer and FMB 6010 FR/catalyst master batch. These two components are supplied in pellet form, and when blended in the proper ratios, will meet various low voltage and specialty wire and cable requirements. AquaGraft® 1-6010 will cure with exposure to moisture at ambient temperature over time (depending on cable construction and environmental conditions). AquaGraft® 1-6010 can also be cured at improved rates if exposed to sauna or hot water after extrusion. APPLICATIONS AquaGraft® 1-6010 is designed for use in various low voltage applications including building wire, control cables, submersible pump cables, and other specifications requiring superior thermal, mechanical, and electrical properties. This two-component system, when blended in an 80% PEMC-1: 20% FMB 6010 blend ratio, will yield a finished compound which will allow the cable to pass various industry recognized flame tests and perform well for UL-44 building wire applications. SPECIFICATIONS When extruded and cured consistent with standard safe wire and cable industry practices, cable insulated with AquaGraft® 1-6010 will comply with the requirements as specified in the following standards: UL 44 XHH, XHHW, XHHW-2, RHH, RHW, RHW-2, and SIS CSA 22.2 No. 38-05 for RW-75, RWU-75, R-90, RW-90 FT-2 Flame, UL Horizontal Flame

150°C RATED MOISTURE CROSS LINKABLE XLPO SYSTEM CONSISTING OF GRAFTED XLPO BASE AND FLAME RETARDANT CATALYST MASTER BATCH (RoHS COMPLIANT) DESCRIPTION AquaGraft 1-5150 is a moisture crosslinkable, natural, XLPO grafted polymer system that is composed of PEMC-1 and FMB-5150 FR/catalyst master batch. These two components are supplied in pellet form, and when blended in the proper ratios, will meet various low voltage and specialty wire and cable requirements. AquaGraft 1-5150 will cure with exposure to moisture at ambient temperature with time (depending on cable construction and environmental conditions). AquaGraft 1-5150 can also be cured at accelerated rates by exposure to sauna or hot water after extrusion. APPLICATIONS AquaGraft 1-5150 is designed for use in UL/CSA 150°C rated AWM cable applications. These two components, when blended in a 70% PEMC-1/30% FMB-5150 blend ratio, will yield a finished compound which will allow the cable to pass various industry recognized requirements and be suitable for flame retardant 150oC applications. SPECIFICATIONS When extruded and cured consistent with standard safe wire and cable industry practices, cable insulated with the correct component ratios will comply with the requirements as specified in the following standards: UL 150 C Styles 3321 CSA CL-1503 Class 1, Group A/B single conductor 600v XLPE FT-2 Flame Rating, UL Horizontal Flame

MOISTURE CROSSLINKABLE MULTI-COMPONENT SYSTEM BASED ON GRAFTED XLPO POLYMER FOR LOW VOLTAGE WIRE APPLICATIONS (RoHS COMPLIANT) DESCRIPTION AquaGraft® 16-6010 is a moisture crosslinkable, natural, XLPO grafted polymer system that is composed of EPMC-16 grafted base polymer and FMB 6010 FR/catalyst master batch. These two components are supplied in pellet form, and when blended in the proper ratios, will meet various low voltage and specialty wire and cable requirements. AquaGraft® 16-6010 will cure with exposure to moisture at ambient temperature over time (depending on cable construction and environmental conditions). AquaGraft® 16-6010 can also be cured at improved rates if exposed to sauna or hot water after extrusion. APPLICATIONS AquaGraft® 16-6010 is designed for use in various low voltage applications including building wire, control cables, submersible pump cables, and other specifications requiring superior thermal, mechanical, and electrical properties. This two-component system, when blended in an 80% EPMC-16: 20% FMB 6010 blend ratio, will yield a finished compound which will allow the cable to pass various industry recognized flame tests and perform well for UL-44 building wire applications. SPECIFICATIONS When extruded and cured consistent with standard safe wire and cable industry practices, cable insulated with AquaGraft® 16-6010 will comply with the requirements as specified in the following standards: UL 44 RHH, RHW, RHW-2, and SIS CSA 22.2 No. 38-05 for RW-75, RWU-75, R-90, RW-90 FT-2 Flame, UL Horizontal Flame

MOISTURE CROSSLINKABLE MULTI-COMPONENT SYSTEM BASED ON GRAFTED XLPO POLYMER FOR LOW VOLTAGE WIRE APPLICATIONS (RoHS COMPLIANT) DESCRIPTION AquaGraft 16-100 is a moisture crosslinkable, natural, XLPO grafted polymer system that is composed of EPMC 16 grafted base polymer, CMB 432 catalyst master batch and FMB 5008 FR/catalyst master batch. These three components are supplied in pellet form, and when blended in the proper ratios, will meet various low voltage and specialty wire and cable requirements. AquaGraft 16-100 will cure with exposure to moisture at ambient temperature over time (depending on cable construction and environmental conditions). AquaGraft 16-100 can also be cured at improved rates if exposed to sauna or hot water after extrusion. APPLICATIONS AquaGraft 16-100 is designed for use in various low voltage applications including building wire, control cables, submersible pump cables, and other specifications requiring superior thermal, mechanical, and electrical properties. This three component system, when blended in a 68/2/30 blend ratio, will yield a finished compound which will allow the cable to pass various industry recognized flame tests and perform well for UL-44 building wire applications. SPECIFICATIONS When extruded and cured consistent with standard safe wire and cable industry practices, cable insulated with AquaGraft 16-100 will comply with the requirements as specified in the following standards: UL 44 XHH, XHHW, XHHW-2, RHH, RHW, RHW-2, and SIS CSA 22.2 No. 38-05 for RW-75, RWU-75, R-90, RW-90 FT-2 Flame, UL Horizontal Flame

150° C RATED FLEXIBLE MOISTURE CROSS LINKABLE XLPO SYSTEM CONSISTING OF GRAFTED ELASTOMERIC XLPO BASE AND FLAME RETARDANT CATALYST MASTER BATCH (RoHS COMPLIANT) ESCRIPTION AquaGraft 16-5150 is a flexible moisture crosslinkable, natural, XLPO grafted polymer system that is composed of EPMC-16 and FMB-5150 FR/catalyst master batch. These two components are supplied in pellet form, and when blended in the proper ratios, will meet various low voltage and specialty wire and cable requirements. AquaGraft 16-5150 will cure with exposure to moisture at ambient temperature with time (depending on cable construction and environmental conditions). AquaGraft 16-5150 can also be cured at accelerated rates by exposure to sauna or hot water after extrusion. APPLICATIONS AquaGraft 16-5150 is designed for use in UL/CSA 150°C rated AWM cable applications. These two components, when blended in a 70% EPMC-16/30% FMB-5150 blend ratio, will yield a finished compound which will allow the cable to pass various industry recognized requirements and be suitable for flame retardant 150oC applications. SPECIFICATIONS When extruded and cured consistent with standard safe wire and cable industry practices, cable insulated with the correct component ratios will comply with the requirements as specified in the following standards: UL 150 C Styles 3321 CSA CL-1503 Class 1, Group A/B single conductor 600v XLPE FT-2 Flame Rating, UL Horizontal Flame SAE J1127

125°C RATED, HIGHLY FLEXIBLE MOISTURE CROSS LINKABLE EPR SYSTEM CONSISTING OF GRAFTED ELASTOMERIC EPR BASE AND FLAME RETARDANT CATALYST MASTER BATCH (RoHS COMPLIANT) DESCRIPTION AquaGraft® 2-5150 is a highly flexible moisture crosslinkable, natural, EPR based grafted polymer system that is composed of EPMC-2 and FMB-5150 FR/catalyst master batch. These two components are supplied in pellet form, and when blended in the proper ratios, will meet various low voltage and specialty wire and cable requirements. AquaGraft® 2-5150 will cure with exposure to moisture at ambient temperature with time (depending on cable construction and environmental conditions). AquaGraft® 2-5150 can also be cured at accelerated rates by exposure to sauna or hot water after extrusion. APPLICATIONS AquaGraft® 2-5150 is designed for use in a variety of 125°C automotive cable applications. These two components, when blended in a 70% EPMC-2/30% FMB-5150 blend ratio, will yield a finished compound which will allow the cable to pass various industry recognized requirements and be suitable for flame retardant 125oC applications. SPECIFICATIONS When extruded and cured consistent with standard safe wire and cable industry practices, cable insulated with the correct component ratios will comply with the requirements as specified in the following standards: ISO 6722 SAE J1127 FT-2 Flame Rating, UL Horizontal Flame

HALOGEN FREE, FLAME RETARDANT, (HFFR) MOISTURE CROSSLINKABLE SYSTEM FOR LOW VOLTAGE WIRE INSULATING AND CABLE JACKETING APPLICATIONS (RoHS COMPLIANT) DESCRIPTION AquaGraft® 7020 is a moisture crosslinkable, natural, XLPO composition designed to be used with CMB-6001 catalyst master batch at a ratio of 93:7. All components are supplied in pellet form and when homogeneously blended in the recommended ratios, will meet numerous low voltage insulating and cable jacketing requirements. When combined with CMB 6001 in the recommended ratio, AquaGraft® 7020 will cure with controlled exposure to moisture using a sauna or hot water after extrusion. APPLICATIONS AquaGraft® 7020 is designed for use in various applications including building wire, control cables, tray cables, photovoltaic, power and telecom cable jacketing applications, and other specifications requiring superior flame, thermal, and mechanical properties. This two-component system, when blended in the appropriate ratio, will yield a finished compound which will allow the cable to pass various industry recognized flame and cable tests. SPECIFICATIONS When extruded and cured consistent with standard safe and acceptable wire and cable industry practices, cable insulated with AquaGraft® 7020 is designed to comply with the requirements as specified in the following standards. It is important to note that overall cable construction plays an important role in flame, fluid, and electrical performance. IEEE 383/UL-1685 IEEE 1202 - FT2 Flame Exposure ICEA S-73-532/ NYC Transit TUV 2Pfg1169:2007 EN 50618:2014

HALOGEN FREE, HIGHLY FLAME RETARDANT, (HFFR) MOISTURE CROSSLINKABLE SYSTEM FOR LOW VOLTAGE WIRE INSULATING AND CABLE JACKETING APPLICATIONS (RoHS COMPLIANT) DESCRIPTION AquaGraft® 8020 is a moisture crosslinkable, natural, XLPO composition designed to be used with CMB-6001 catalyst master batch at a ratio of 93:7. All components are supplied in pellet form and when homogeneously blended in the recommended ratios, will meet numerous low voltage insulating and cable jacketing requirements. When combined with CMB 6001 in the recommended ratio, AquaGraft® 8020 will cure with controlled exposure to moisture using a sauna or hot water after extrusion. APPLICATIONS AquaGraft® 8020 is designed for use in various applications including building wire, control cables, tray cables, photovoltaic, power and telecom cable jacketing applications, and other specifications requiring superior flame, thermal, and mechanical properties. This two-component system, when blended in the appropriate blend ratio, will yield a finished compound which will allow the cable to pass various industry recognized flame and cable tests. SPECIFICATIONS When extruded and cured consistent with standard safe and acceptable wire and cable industry practices, cable insulated with AquaGraft® 8020 is designed to comply with the requirements as specified in the following standards. It is important to note that overall cable construction plays an important role in flame, fluid, and electrical performance. IEEE 1202 - FT4 Flame Exposure IEEE 383/UL-1685 ICEA S-73-532/ NYC Transit TUV 2Pfg1169:2007 EN 50618:2014

GRAFTED XLPO BASE FOR USE IN MOISTURE CROSSLINKABLE APPLICATIONS (RoHS COMPLIANT) DESCRIPTION Natural, unfilled grafted polymer base in pellet form designed to be used in moisture crosslinkable applications for power and control cables requiring added flexibility and excellent electrical properties. AquaGraft EPMC-16 will cure with exposure to moisture at ambient temperature over a time (depending on cable construction and environmental conditions.) AquaGraft EPMC-16 can also be cured at improved rates if exposed to sauna or hot water after extrusion. APPLICATIONS AquaGraft EPMC-16 is designed for use in low to medium voltage (5kv) power cable applications. AquaGraft EPMC-16, when used in correct ratios with available Flame Retardant masterbatch will allow the cable to pass various industry recognized flame tests and perform in wet environments up to 90oC in applications SPECIFICATIONS When extruded and cured consistent with standard safe wire and cable industry practices, cable insulated with the correct ratios AquaGraft EPMC-16 and FMB Masterbatch/CMB-432 will comply with the requirements as specified in the following standards: Power Cable up to 5Kv UL 44 for: XHHW, XHHW-2 RHW, RHW-2 RHH SIS USE, USE-2 Horizontal Flame VW-1 on larger cable sizes

EXTRA FLEXIBLE GRAFTED EPR BASE FOR USE IN MOISTURE CROSSLINKABLE APPLICATIONS (RoHS COMPLIANT) DESCRIPTION Natural, unfilled grafted polymer base in pellet form designed to be used in moisture crosslinkable applications for power and control cables requiring excellent flexibility and excellent electrical properties. AquaGraft EPMC-2 will cure with exposure to moisture at ambient temperature over a time (depending on cable construction and environmental conditions.) AquaGraft EPMC-2 can also be cured at improved rates if exposed to sauna or hot water after extrusion. APPLICATIONS AquaGraft EPMC-2 is designed for use in low to medium voltage (5kv) power cable applications. AquaGraft EPMC-2, when used in correct ratios with available Flame Retardant masterbatch will allow the cable to pass various industry recognized flame tests and perform in wet environments up to 90oC in applications SPECIFICATIONS When extruded and cured consistent with standard safe wire and cable industry practices, cable insulated with the correct ratios AquaGraft EPMC-2 and FMB Masterbatch/CMB-432 will comply with the requirements as specified in the following standards: Power Cable up to 5Kv UL 44 for: RHW, RHW-2 RHH SIS USE, USE-2 Horizontal Flame Vertical Flame VW-1 Flammability Test

GRAFTED EPR BASE FOR USE IN MOISTURE CROSSLINKABLE APPLICATIONS (RoHS COMPLIANT) DESCRIPTION Natural, unfilled grafted polymer base in pellet form designed to be used in moisture crosslinkable applications for power and control cables requiring added flexibility and excellent electrical properties. AquaGraft EPMC-4 will cure with exposure to moisture at ambient temperature over a time (depending on cable construction and environmental conditions.) AquaGraft EPMC-4 can also be cured at improved rates if exposed to sauna or hot water after extrusion. APPLICATIONS AquaGraft EPMC-4 is designed for use in low to medium voltage (5kv) power cable applications. AquaGraft EPMC-4, when used in correct ratios with available Flame Retardant masterbatch will allow the cable to pass various industry recognized flame tests and perform in wet environments up to 90oC in applications SPECIFICATIONS When extruded and cured consistent with standard safe wire and cable industry practices, cable insulated with the correct ratios AquaGraft EPMC-4 and FMB Masterbatch/CMB-432 will comply with the requirements as specified in the following standards: Power Cable up to 5Kv UL 44 for: XHHW, XHHW-2 RHW, RHW-2 RHH SIS USE, USE-2 Horizontal Flame Vertical Flame VW-1 Flammability Test

GRAFTED POLYOLEFIN BASE FOR USE IN MOISTURE CROSSLINKABLE APPLICATIONS (RoHS COMPLIANT) DESCRIPTION Unfilled grafted polymer base in pellet form designed to be used in moisture crosslinkable applications for power, control, and appliance cables requiring excellent thermal, mechanical, and electrical properties. AquaGraft PEMC-1 will cure with exposure to moisture at ambient temperature over a time (depending on cable construction and environmental conditions.) AquaGraft PEMC-1 can also be cured at improved rates if exposed to sauna or hot water after extrusion. APPLICATIONS AquaGraft PEMC-1 is designed for use in low voltage (2kv) wire and cable applications. AquaGraft PEMC-1, when used in correct ratios with available Flame Retardant masterbatch will allow the cable to pass various industry recognized flame tests and perform in wet electrical applications as well as high temperature appliance constructions. SPECIFICATIONS When extruded and cured consistent with standard safe wire and cable industry practices, cable insulated with the correct ratios AquaGraft PEMC-1 and FMB Masterbatch/CMB-432 will comply with the requirements as specified in the following standards: UL 44 for: XHHW, XHHW-2 SIS, USE, USE-2 UL/CSA AWM applications up to 150C Horizontal Flame* VW-1 on larger cable sizes* *(When used with appropriate level of FR master-batch)

35% Mineral Glass Fiber Reinforced, Flame Retardant Formerly known as EnCounter 1F035MGF

A heat and UV stable halogenated masterbatch Note: Additional custom color matching is available upon request. GPP3003C is a flame-retardant concentrate designed to impart flame resistance to polypropylene systems in an efficient, dust-free delivery system. Dependent upon let-down ratio in extrusion or molding grade resins, GPP3003C can provide the following flammability characteristics: UL-94 V-0 at 2 to 5:1 UL-94 V-2 at 6 to 12:1 (UL-94: Test for Flammability of Plastic Materials for Parts in Devices and Appliances) GPP3003C performance in a specific resin system may be submitted to Underwriters Laboratories for confirmatory UL Recognition.

MEP52 0000 Mixed Engineered Polymer Granules Axplas MEP52 0000 grade is a mix of clean, washed granular chips rich in PS and ABS with regular particle size. Minor quantities of rubber and wood are present. Please note the composition chart is a typical result and that all material fractions may vary by a few percent around the numbers shown on the pie chart. Produced from 100% recycled content, this product offers a range of user benefts, including: - Low carbon input can reduce your carbon footprint - Environmental gains from resource effciency Cost savings on raw materials Axplas MEP52 0000 is available in 1 tonne polyester big bags on a pallet, other formats possible on request. Applications: - Feedstock material for separation of PS and ABS - Plastics wood manufacture - Blending agent or filler for mixed plastics products - Manufacture of panels, sheets and boards

MEP52 0000W Mixed Engineered Polymer Granules Axplas MEP52 0000W grade is a mix of clean, washed granular chips rich in PS and ABS with regular particle size. Minor quantities of rubber and wood are present. Please note the composition chart is a typical result and that all material fractions may vary by a few percent around the numbers shown on the pie chart. Produced from 100% recycled content, this product offers a range of user benefts, including: - Low carbon input can reduce your carbon footprint - Environmental gains from resource ef?ciency - Cost savings on raw materials Applications: - Feedstock material for separation of PS and ABS - Plastics wood manufacture - Blending agent or filler for mixed plastics products - Manufacture of panels, sheets and boards

MEP52 0074 Mixed engineering polymers granules Axplas® MEP52 0074 grade is a mix of clean, washed granular chips rich in PP with regular particle size. Minor quantities of wood and rubber are also present. Please note the composition chart is a typical result and that all material fractions may vary by a few percent around the numbers shown on the pie chart. Produced from 100% recycled content, this product offers a range of user benefits, including: - Low carbon input can reduce your carbon footprint - Environmental gains from resource efficiency - Cost savings on raw material Applications: - Feedstock material for separation of PS and ABS - Plastics wood manufacture - Blending agent or filler for mixed plastics products - Manufacture of panels, sheets and boards

MEP52 0075 Mixed engineering polymers granules Axplas® MEP52 0075 grade is a mix of clean, washed granular chips rich in PP with regular particle size. Minor quantities of wood and rubber are also present. Please note the composition chart is a typical result and that all material fractions may vary by a few percent around the numbers shown on the pie chart. Produced from 100% recycled content, this product offers a range of user benefits, including: - Low carbon input can reduce your carbon footprint - Environmental gains from resource efficiency - Cost savings on raw material Applications: - Feedstock material for separation of PS and ABS - Plastics wood manufacture - Blending agent or filler for mixed plastics products - Manufacture of panels, sheets and boards

MEP52 4000 Mixed Engineered Polymer reduced Rubber Axplas MEP52 4000 grade is a mix of clean, washed granular chips rich in PS and ABS with regular particle size. Minor quantities of rubber and wood are present. Please note the composition chart is a typical result and that all material fractions may vary by a few percent around the numbers shown on the pie chart. Produced from 100% recycled content, this product offers a range of user benefits, including: - Low carbon input can reduce your carbon footprint - Environmental gains from resource efficiency - Cost savings on raw materials Applications: - Feedstock material for separation of PS and ABS - Plastics wood manufacture - Blending agent or filler for mixed plastics products - Manufacture of panels, sheets and boards

MEP52 7081 Mixed engineering PIM powder Axplas® MEP52 7081 grade is a special blend of polymer powders created for the moulding process known as PIM (Powder Impression Moulding). MEP52 7081 is a clean, size reduced styrenic-rich blend of engineering plastics. Typical particle size distribution: >98% is below 1000 micron. Very small fractions of wood and rubber may be present. Produced from 100% recycled content, this product offers a range of user benefits, including: - Low carbon input can reduce your carbon footprint - Environmental gains from resource efficiency - Cost savings on raw material - PIM moulded items can be recycled at the end of useful life Applications: - Manufacture of PIM 100% recyclable plastic sheets and boards or other shaped products - Rotational moulding of complex 3D shapes - Other compression moulded items

MEP53 0000 Mixed Engineered Polymer Granules Axplas MEP53 0000 grade is a mix of clean, washed granular chips rich in PS and ABS with regular particle size. Minor quantities of rubber and wood are present. Please note the composition chart is a typical result and that all material fractions may vary by a few percent around the numbers shown on the pie chart. Produced from 100% recycled content, this product offers a range of user benefits, including: - Low carbon input can reduce your carbon footprint - Environmental gains from resource ef?ciency - Cost savings on raw materials Applications: - Feedstock material for separation of PS and ABS - Plastics wood manufacture - Blending agent or filler for mixed plastics products - Manufacture of panels, sheets and boards

BITONER BT-100 is thermoplastic, low molecular weight, slightly yellow aliphatic resin. With good affinity with a wide range of fillers,it is used as a binder in thermoplastic road marking paints. Owing to its excellent tack and tack retention,it is also used in hot melt adhesives and sealants. This item is also used as processing and reinforcing agent in tyre and rubber compounds. Characteristics: - Excellent affinity with wide range of fillers - Low Molecular weight - Good chemical stability - Water resistance Applications: - Hot Melt Adhesives - Sealants - Thermoplastic Road Marking Paints - Rubber.

BITONER BT-1102 is thermoplastic, low molecular weight, slightly yellow modified aliphatic resin. It is specially designed to be as binder for Thermoplastic Road Marking Paints. This resin shows excellent affinity for pigments and superior processability in the thermoplastic road marking paints. Characteristics: - Excellent affinity with wide range of fillers - Low Molecular weight - Good chemical stability - Water resistance Applications: - Thermoplastic Road Marking Paints

BITONER BT-1200H is thermoplastic,slightly yellow aliphatic resin,obtained from petroleum-derived monomer. Characterized by wide compatibility with NR,APAO and other polymers,it is used in variety of applications. Characteristics: - Wide compatibility with NR,APAO and other polymers - Good thermal stability - Higher Molecular Weight than BT-1200 - Good chemical stability - Low volatility and low odor - Water resistance Applications: - Hot Melt Adhesives - Sealants - Rubber - Wax Modification - Asphalt Modification

BITONER BT-2104 is thermoplastic, low molecular weight, slightly yellow aliphatic resin obtained from petroleum-derived monomers.Characterized by low molecular weight,narrow MWD,low wax cloud point, good compatibility with APP, APAO, Natural Rubber,SIS,Butyl Rubber and other polymers,this grade is mainly used in PSA,Hot Melt Adhesive and Sealants. Characteristics: - Excellent compatibility with SIS,and other polymers - Good thermal stability - Low Molecular Weight and Narrow MWD - Low Wax Cloud Point - Low volatility and low odor - Water resistance Applications: - HMPSA - Solvent based PSA - Hot Melt Adhesive - Sealants

BITONER BT-2110 is thermoplastic, low molecular weight, slightly yellow aliphatic resin obtained from petroleum-derived monomers.Characterized by low softening point,narrow MWD,low wax cloud point, good compatibility with NR,SIS and other polymers,this grade is mainly used in rubber based PSA. Characteristics: - Excellent compatibility with SIS,and other polymers - Good thermal stability - Low Molecular Weight and Narrow MWD - Low Wax Cloud Point - Low volatility and low odor - Water resistance Applications: - HMPSA - Solvent based PSA - Hot Melt Adhesive - Sealants

BITONER C-2120 is thermoplastic, low molecular weight, light yellow aromatically modified C5 hydrocarbon resin.Characterized by light color,low odor,outstanding heat stability and good compatibility with NR,SIS,EVA, APAO and other polymers, it performs excellent balance of tack and of adhesive and of cohesive properties in rubber based PSA.It is especially suitable for HMPSA. Characteristics: - Excellent compatibility with various polymers and resins - Solubility in various solvents - Low Molecular weight - Low volatility and low odor - Good heat stability Applications: - HMPSA - Solvent based PSA - Hot Melt Adhesive

BITONER BA-120 is thermoplastic,slightly yellow granular aromatic resin obtained from petroleum- derived monomers. It is odor improved grade with extremely low odor and low VOC,good compatibility with other resins and polymers.This grade is specially used in EVA based hot melt adhesives. Characteristics: - Good compatibility with other resins and polymers - Low Molecular weight - Good thermal resistance - Very low VOC and low odor - Water resistance Applications: - Hot Melt Adhesive - Solvent based Adhesives - Printing Ink.

BITONER BP-100 is thermoplastic,slightly yellow granular aromatic resin obtained from petroleum-derived monomers. It is odor improved grade with low odor and low VOC,good compatibility with other resins and polymers.This grade is mainly used in adhesives, esp.EVA based Hot Melt Adhesives. Characteristics: - Good compatibility with EVA,SBS and other polymers - Low Molecular weight - Good thermal resistance - Low VOC and low odor - Water resistance Applications: - Hot Melt Adhesive - Shoes Adhesive - PSA - Industrial Paints - Rubber

BITONER BP-120 is thermoplastic,slightly yellow granular aromatic resin obtained from petroleum-derived monomers. It is odor improved grade with low odor and low VOC,good compatibility with other resins and polymers.This grade is mainly used in adhesives and coatings. Characteristics: - Good compatibility with EVA,SBS and other polymers - Low Molecular weight - Good thermal resistance - Low VOC and low odor - Water resistance Applications: - Hot Melt Adhesive - Shoes Adhesive - Solvent based Adhesive - Industrial Paints - Printing Ink - Asphalt

BITONER C9 BP-140 is thermoplastic, slightly yellow aromatic resin with a low molecular weight. Characterized by much less odor,very low VOC,high softening point and a high level of compatibility with other resins and polymers,it is specially designed for adhesives and printing ink industries. Characteristics: - Excellent compatibility with other resins and polymers - High Softening Point - Good thermal resistance - Low VOC and Low Naphthalne content - Much Less odor Applications: - Hot Melt Adhesive - PSA - Solvent Adhesives - Printing Ink - Asphalt Modification

BITONER C9 BP-150 is thermoplastic, slightly yellow aromatic resin with a low molecular weight. Obtained from petroleum-derived monomers,it is characterized by low odor,high level of compatibility with rosin modified phenolic resin,so it is usually used with phonelic resin in offset ink to decrease the set time and increase the gloss.It is also used in Solvent based Adhesive and Hot Melt Adhesive. Characteristics: - Excellent compatibility with rosin modified phenolic resin - Low Molecular weight - Water resistance Applications: - Printing inks - Hot Melt Adhesives - Solvent Adhesives - PSA.

BITONER H-100 is thermoplastic white color hydrogenated aromatic resin obtained from petroleum-derived monomers. Owing to low odor,good thermal resistance and excellent compatibility,it is used in hot melt adhesives based on EVA, SBS and SIS copolymers. Characteristics: - Excellent compatibility with EVA, SBS,and SIS - Low Molecular weight - Good thermal resistance and water resistance - Low odor and white color Applications: - Hot Melt Adhesives - PSA - Solvent Adhesives - Wax Modification - Plastic Modification.

BITONER H-120 is thermoplastic white color hydrogenated aromatic resin obtained from petroleum-derived monomers. Owing to low odor,good thermal resistance and excellent compatibility,it is used in hot melt adhesives based on EVA, SBS and SIS copolymers. Characteristics: - Excellent compatibility with EVA, SBS and SIS - Low Molecular weight - Good thermal resistance - Low odor and white color - Water resistance Applications: - Hot Melt Adhesives - Solvent Adhesives - Wax Modification

BITONER TR-100 is thermoplastic, low molecular weight, slightly yellow C5 and C9 co-polymerized resin. Possessing the good characters of C5 and C9 hydrocarbon resin,it is characterized by its wide compatibility with EVA,SIS,SBS and other polymers,low cloud point and good heat stability.TR-100 is used in Hot melt adhesives,PSA and shoe adhesives. It is also used as processing and reinforcing agent in tyre and rubber compounds. Characteristics: - Excellent compatibility with various polymers and resins - Solubility in various solvents - Low Molecular weight - Low volatility and low odor - Water resistance Applications: - Hot Melt Adhesive - PSA - Solvent Adhesives - Coatings - Rubber Compounds.