ALCUDIA® 2221F is a low density polyethylene grade, produced by high pressure autoclave technology, suitable for thin blown film applications. This material offers easy processability and good balance of mechanical and optical properties. It contains antioxidant additives. TYPICAL APPLICATIONS - Thin shrink film - Thin pouches - General packaging film - Bubble film - Foams Recommended melt temperature range from 150 to 180°C. Processing conditions should be optimised for each production line.

ALCUDIA® 2221FG is a low density polyethylene grade, produced by high pressure autoclave technology, suitable for thin blown film applications. This material offers easy processability and good balance of mechanical and optical properties. It contains slip (erucamide), antioxidant and antiblock additives. TYPICAL APPLICATIONS - Thin pouches - General packaging film Recommended melt temperature range from 150 to 180°C. Processing conditions should be optimised for each production line.

ALCUDIA® 2303F is a low density polyethylene grade, produced by high pressure tubular technology, suitable for blown or cast film applications. This material offers easy processability and good balance of mechanical and optical properties. It does not contain any additives. TYPICAL APPLICATIONS - General packaging film. - Heavy duty sacks. - Shrink film with high mechanical resistance. Recommended melt temperature range from 180 to 210°C. Processing conditions should be optimised for each production line.

ALCUDIA® 2303FG is a low density polyethylene grade, produced by high pressure tubular technology, suitable for blown or cast film applications. This material offers easy processability, good balance of mechanical and optical properties and excellent draw down. It contains slip additives (oleamide). TYPICAL APPLICATIONS - General packaging film. - Heavy duty sacks. - Shrink film with high mechanical resistance. Recommended melt temperature range from 180 to 210°C. Processing conditions should be optimised for each production line.

ALCUDIA® 2303-FL is stabilized with Ni quencher (yellow greenish colour), UV absorber and antioxidants. This compound offers high solar radiation resistance. APLICATIONS Films for greenhouses and tunnels cover. ALCUDIA® 2303-FL, 180 µm thickness films, have a lifetime of two continuous agricultural seasons (two winters and one summer) in geographical areas where the maximum solar radiation is 160 kLy. For further information, contact to Technical Assistance and Development Department or Commercial Attention Service. Recommended melt temperature range from 190 to 210°C. Processing conditions should be optimised for each production line.

ALCUDIA® 2321FS is a low density polyethylene grade, produced by high pressure autoclave technology, suitable for thin blown film applications. This material offers easy processability and good balance of mechanical and optical properties. It contains slip (erucamide), antioxidant, antiblock and antistatic additives. TYPICAL APPLICATIONS - High-quality packaging films - Packaging of foods, paper and textiles The film can be used either in lay-flat form or converted for applications where low friction is required. Recommended melt temperature range from 150 to 180°C. Processing conditions should be optimised for each production line.

ALCUDIA® 2322M is a low density polyethylene grade of high fluidity intended for those injection moulding applications in which toughness and good flow properties are required. Its formulation does not contain additives. TYPICAL APPLICATIONS Due to its good properties balance, ALCUDIA® 2322M is a very versatile grade and is suitable for articles of very diverse sizes: - Industrial parts and components. - Caps and closures. - Toys. Recommended melt temperature range from 180 to 230°C. Processing conditions should be optimised for each production line.

ALCUDIA® 2335FG is a low density polyethylene grade, produced by high pressure autoclave technology, suitable for thin blown film or cast film applications. This material offers easy processability and good balance of mechanical and optical properties. It contains high concentration of slip (erucamide), antioxidant and antiblock additives. TYPICAL APPLICATIONS - Pouches with good slip and optical properties. - Automatic packaging - Thin shrink films - Bags for the textile industry Recommended melt temperature range from 140 to 165°C. Processing conditions should be optimised for each production line.

ALCUDIA® 2605F is a low density polyethylene grade, produced by high pressure autoclave technology, suitable for blown film applications. This material offers easy processability and good balance of mechanical and optical properties. It contains antioxidant additives. TYPICAL APPLICATIONS - Shrink films / hoods - Coextruded films where good optical properties and heat resistance is required. Recommended melt temperature range from 170 to 200°C. Processing conditions should be optimised for each production line.

ALCUDIA® 2625FG is a low density polyethylene grade, produced by high pressure autoclave technology, suitable for thin blown film or cast film applications. This material offers easy processability, good optical properties and enhanced toughness. It contains slip (erucamide), antioxidant and antiblock additives. TYPICAL APPLICATIONS - Pouches with good slip and optical properties. - Automatic packaging - Lamination. Recommended melt temperature range from 140 to 165°C. Processing conditions should be optimised for each production line.

ALCUDIA® 2805F is a low density polyethylene grade, produced by high pressure autoclave technology, suitable for blown film applications. This material offers easy processability and an excellent balance of mechanical and optical properties. It contains antioxidant. TYPICAL APPLICATIONS - Shrink films / hoods - Coextruded films with good optical properties and excellent mechanical properties Recommended melt temperature range from 170 to 210°C. Processing conditions should be optimised for each production line.

ALCUDIA® 2810F is a low density polyethylene grade, produced by high pressure autoclave technology, suitable for blown film applications. This material offers easy processability and good balance of mechanical and optical properties. It contains antioxidant. TYPICAL APPLICATIONS - Shrink films / hoods - Coextruded films with good optical properties and excellent mechanical resistance Recommended melt temperature range from 170 to 210°C. Processing conditions should be optimised for each production line.

ALCUDIA® 2820F is a low density polyethylene grade, produced by high pressure autoclave technology, suitable for thin blown film or cast film applications. This material offers easy processability and good balance of mechanical and optical properties. It contains antioxidant. TYPICAL APPLICATIONS - Pouches with good optical properties - Automatic packaging - Lamination Recommended melt temperature range from 160 to 200°C. Processing conditions should be optimised for each production line.

ALCUDIA® 2820FG is a low density polyethylene grade, produced by high pressure autoclave technology, suitable for thin blown film or cast film applications. This material offers easy processability and good balance of mechanical and optical properties. It contains slip (erucamide), antiblock and antioxidant additives. TYPICAL APPLICATIONS - Pouches with good optical properties - Automatic packaging - Lamination Recommended melt temperature range from 160 to 200°C. Processing conditions should be optimised for each production line.

ALCUDIA® 3235F is a low density polyethylene grade, produced by high pressure autoclave technology, suitable for thin blown film or cast film applications. This material is easily processed, and films are characterised by easy tear, enhanced toughness and good optical properties. It contains antioxidant additive. TYPICAL APPLICATIONS - Hygiene overwrap films - Easy tear films - Display packaging Recommended melt temperature range from 150 to 190°C. Processing conditions should be optimised for each production line.

ALCUDIA® 3235FG is a low density polyethylene grade, produced by high pressure autoclave technology, suitable for thin blown film or cast film applications. This material offers easy processability and films characterised by easy tear, good optical properties and enhanced toughness. It contains slip (erucamide), antioxidant and high level of antiblock additives. TYPICAL APPLICATIONS - Hygiene overwrap films - Easy tear films - Display packaging Recommended melt temperature range from 150 to 190°C. Processing conditions should be optimised for each production line.

ALCUDIA® 3235FGA is a low density polyethylene grade, produced by high pressure autoclave technology, suitable for thin blown film or cast film applications. This material offers easy processability and films characterised by easy tear, good optical properties and enhanced toughness. It contains slip (erucamide), antioxidant and antiblock additives. TYPICAL APPLICATIONS - Hygiene overwrap films - Easy tear films - Display packaging Recommended melt temperature range from 150 to 190°C. Processing conditions should be optimised for each production line.

ALCUDIA® 3235FGD is a low density polyethylene grade, produced by high pressure autoclave technology, suitable for thin blown film or cast film applications. The easy processability of this grade allows high extrusion speeds at low gauges. This material combines easy tear, enhanced toughness and good optical properties. It contains high level of slip (erucamide), antiblock and antioxidant additives. TYPICAL APPLICATIONS - Hygiene overwrap films - Easy tear films - Display packaging Recommended melt temperature range from 150 to 190°C. Processing conditions should be optimised for each production line.

ALCUDIA® CA-2130A is stabilized with HALS (colourless) and antioxidants. This compound offers high solar radiation resistance. APPLICATIONS Films for greenhouses and tunnels cover. ALCUDIA® CA-2130A, 180 µm thickness films have a lifetime of two continuous agricultural seasons (two winters and one summer) in geographical areas where maximum solar radiation is 160 kLy. For further information, contact to Technical Assistance and Development Department or Commercial Attention Service. Recommended melt temperature range from 190 to 210°C. Processing conditions should be optimised for each production line.

ALCUDIA® compound CN-102 has been esencially developed for coating of steel pipe using extrusion techniques. Furthermore it is designed for steelpipe coating to comply with the requirements of the DIN-30670 specification standard. CN-102 is a high viscosity high molecular weight low density polyethylene black compound which offers easy processing combined with smooth glossy surface finish, excellent resistance to mechanical deformation and corrosion. The combination of the antioxidant system and minimun of 2.2% well dispersed carbon black used in CN-102 provides the following features: - excellent protection against thermal oxidation during processing. - long term stability. - excellent protection against outdoor weathering. Because of the good mechanical properties and their characteristics, the polyethylene black compound ALCUDIA® CN-102, is designed to produce pipe.

ALCUDIA® CN-105 is based on a special low density polyethylene, which provides excellent properties to the final product. It is characterized by its excellent environmental stress cracking resistance (ESCR), good processability and low temperature performance. This grade contains well dispersed carbon black in order to ensure good outdoor weather resistance and antioxidant to improve the thermal ageing properties. TYPICAL APPLICATIONS Black jacketing of telecommunication cables. ALCUDIA® CN-105 processing conditions depend mainly on the type of extrusion equipment but as a guiding idea, it is recommended a temperature profile between 150 - 210°C. ALCUDIA® CN-105 meets the following specifications: ISO 1872 PE KHC 23D003; ASTM D 1248 I,C5 Grade J3; NF C 32-060 GE1; VDE 0207 Teil3 2YM2.

ALCUDIA® CP-104 is a natural and cross-linkable compound based on low density polyethylene, specifically designed to be cross-linked by organic peroxide. It contains a special antioxidant to guarantee thermal stability and causes minimum interference with the cross-linking process. The outstanding features of this grade are cleanliness, excellent thermal stability, good processing behaviour, excellent cross-linking efficiency at high speed and smooth surface finish. ALCUDIA® CP-104 is normally supplied in octabins, tankers and van-boxes. TYPICAL APPLICATIONS Medium voltage power cable insulation. Processing conditions of ALCUDIA® CP-104 are dependent on formulation and technique employed but it is noteworthy that this grade is suitable to use in a temperature range of 120°C - 130°C. ALCUDIA® CP-104 meets the following standards: ISO 1872 PE KHN 18D022; ASTM D 1248 I,A3 Grade E5.

ALCUDIA® CP-121 is high molecular weight, low density polyethylene compound designed for telephone and coaxial cables. This product provides a superior performance at high-speed extrusion together with a smooth surface finish of the cable. This grade contains a special stabilization system for protection against thermal and shear degradation during processing and it also contains a metal deactivator to ensure long-term ageing properties. TYPICAL APPLICATIONS Solid insulation for telephone cables It is recommended a temperature profile between 150 - 220°C. Optimal processing conditions must be tuned for each production line, recommending to use filters and a break plate to increase the pressure in the cylinder and consequently improve the cable quality, homogenization and dispersion of pigments in the case of colored cable ALCUDIA® CP-121 meets the following specifications: ISO 1872 PE KHN 23D003; ASTM D 1248 I, A5, Grade E5; NF C 32-060 ISM1; VDE 0207 Teil 2 24I1.

ALCUDIA® PE003 is a low density polyethylene grade, produced by high pressure autoclave technology, suitable for blown or cast film applications. It is also used to make little containers by extrusion-blow moulding. This material offers easy processability and good balance of mechanical and optical properties. It does not contain any additives. TYPICAL APPLICATIONS - General packaging film and thin shrink film. - Lamination to different substrates (paper, aluminium foil, etc), with or without adhesive. - T Extrusion-blow moulding of up to 2 litres containers for contact with foodstuffs. Recommended melt temperature range from 150 to 180°C. Processing conditions should be optimised for each production line. ALCUDIA® PE-003 is a low density polyethylene developed for cross-linking by direct addition of organic peroxide or silanes. This grade has the following features: excellent processability, high cross-linking rate and smooth surface finish. This product does not contain additives, so antioxidant must be added. The nature and content of antioxidant ought to be treated carefully because of which should present minimum interference with the cross-linking reaction and ensure thermal stability. TYPICAL APPLICATIONS Insulation of low voltage cables. The ALCUDIA® PE-003 processing conditions depend on the type of cable to be manufactured, kind of equipment used and cross-linking system. The use of filters and a break plate is recommended in order to increase pressure in the cylinder and to avoid contaminations that could decrease the final quality of the cable. ALCUDIA® PE-003 meets the following standards: ISO 1872 PE KN 18D022; ASTM D 1248 I, A3 Grade E5.

ALCUDIA® PE-004 is a natural and crosslinkable low density polyethylene specifically designed to be cross-linked by organic peroxide. The outstanding features of this grade are cleanliness, excellent processability, high efficiency of crosslinking, good mechanical properties and smooth surface finish. This grade does not contain antioxidant, therefore, it is necessary to add in proper balance of a non-staining antioxidant and peroxide to ensure thermal stability and optimum cure level. ALCUDIA® PE-004 is normally supplied in octabins, tankers and van-boxes. TYPICAL APPLICATIONS Medium voltage cable insulation. Processing conditions of ALCUDIA® PE-004 are dependent on formulation and technique employed but it is noteworthy that this grade is suitable to use in a temperature range of 120°C - 130°C. ALCUDIA® PE-004 meets the following standards: ISO 1872 PE KHN 18D022; ASTM D 1248 I, A3 Grade E5.

ALCUDIA® PE015 is a low density polyethylene grade, produced by high pressure autoclave technology, suitable for blown or cast film applications. It is also used to make little containers by extrusion-blow moulding. This material offers easy processability and good balance of mechanical and optical properties. It does not contain any additives. TYPICAL APPLICATIONS - General packaging film and shrink film with high mechanical resistance. - Medium duty sacks. - Extrusion-blow moulding of up to 2 litres containers for contact with foodstuffs. Recommended melt temperature range from 170 to 190°C. Processing conditions should be optimised for each production line.

ALCUDIA® PE017 is a low density polyethylene grade, produced by high pressure autoclave technology, suitable for extrusion coating and injection moulding applications. This material offers a good balance between easy processability and stiffness. It does not contain any additives. TYPICAL APPLICATIONS - Extrusion coating. - Injection moulding. Recommended melt temperature range for extrusion coating from 275 to 330°C. Processing conditions should be optimised for each production line.

ALCUDIA® PE019 is a low density polyethylene grade of high fluidity intended for those injection moulding applications in which toughness and good flow properties are required. Its formulation does not contain additives. TYPICAL APPLICATIONS Due to its good properties balance, ALCUDIA® PE019 is a very versatile grade and is suitable for articles of very diverse sizes: - Industrial parts and components. - Caps and closures. - Toys. Recommended melt temperature range from 180 to 230°C. Processing conditions should be optimised for each production line.

ALCUDIA® PE022 is a low density polyethylene grade of very high fluidity, intended for injection moulding applications due to very low viscosity that allows an easy filling of the moulds, even with complex geometry, and it is very versatile to disperse pigments. It does not contain any additives. TYPICAL APPLICATIONS Due to its good properties balance, ALCUDIA® PE022 is a very versatile grade and is suitable for articles of very diverse sizes: - Caps and closures. - Toys. - Component in the preparation of masterbatches and blends with waxes and other polymers. Recommended melt temperature range from 180 to 230°C. Processing conditions should be optimised for each production line.

ALCUDIA® PE023 is a low density polyethylene grade of very high fluidity, intended for diverse applications such as hot-melt adhesives, coatings, compounds and master-batches. Its formulation does not include additives. TYPICAL APPLICATIONS - Hot-melt adhesives - Coatings - Viscosity modification in blends - Compounds - Master-batches Recommended melt temperature range from 180 to 230°C. Processing conditions should be optimised for each production line.

ALCUDIA® PE033 is a low density polyethylene grade, produced by high pressure autoclave technology, suitable for blown or cast film applications. This material offers easy processability and good balance of mechanical and optical properties. It contains antioxidant additive. TYPICAL APPLICATIONS - General packaging film. - Shrink film with high mechanical resistance. - Heavy duty sacks. Recommended melt temperature range from 190-220°C. Processing conditions should be optimised for each production line.

ALCUDIA® PE034/A is a low density polyethylene grade, produced by high pressure autoclave technology, suitable for blown or cast film applications. This material offers easy processability and good balance of mechanical and optical properties. It contains antioxidant additive and antiblock additives. TYPICAL APPLICATIONS - General packaging film. - Shrink film with high mechanical resistance. - Heavy duty sacks. Recommended melt temperature range from 190-220°C. Processing conditions should be optimised for each production line.

ALCUDIA® PE045/A is a low density polyethylene grade, produced by high pressure autoclave technology, suitable for blown or cast film applications. This material offers easy processability, good balance of slip, mechanical and optical properties and excellent draw down. It contains antistatic, slip and antiblock additives. TYPICAL APPLICATIONS - General packaging film. - Film for lamination with adhesives. - Film for automated packaging. - High clarity, medium-high slip film. Recommended melt temperature range from 150 to 180°C. Processing conditions should be optimised for each production line.

ALCUDIA® PE046/A is a low density polyethylene grade, produced by high pressure autoclave technology, suitable for blown or cast film applications. This material offers easy processability, good balance of slip, mechanical and optical properties and excellent draw down. It contains slip and antiblock additives. TYPICAL APPLICATIONS - General packaging film. - Film for lamination with adhesives. - Lamination to different substrates (paper, aluminium foil, etc), with or without adhesives. - High clarity, medium-high slip film. Recommended melt temperature range from 150 to 180°C. Processing conditions should be optimised for each production line.

ALCUDIA® PE063/A is a low density polyethylene grade, produced by high pressure autoclave technology, suitable for blown or cast film applications. This material offers easy processability into thin films with good balance of slip, mechanical and optical properties. It contains slip and antiblock additives. TYPICAL APPLICATIONS - Film for automated packaging. - High slip thin film. Recommended melt temperature range from 140 to 160°C. Processing conditions should be optimised for each production line.

ALCUDIA® PE071 is a low density polyethylene grade, produced by high pressure autoclave technology, especially intended for extrusion coating. This material offers an adequate balance between easy processability, good organoleptic properties, excellent adhesion and low neck-in. It does not contain any additives. TYPICAL APPLICATIONS - Extrusion coating. - Coextruded thin film. - Injection moulding. The excellent draw down properties of ALCUDIA® PE-071 allow high-speed coatings, up to 850 m/min and 5 g/m² at a maximum extrusion temperature of 330°C. This material has a very low neck-in throughout a wide range of extrusion conditions. Recommended melt temperature range for extrusion coating from 275 to 330°C. Temperature range for coextrusion depending on the processed polymers. Processing conditions should be optimised for each production line.

ALKATEQ™ LDN248P1200 is a natural, unpigmented, low density polyethylene ground powder with a maximum particle size of <1200 micron. ALKATEQ™ LDN248P1200 conforms to the requirements of the United States Food and Drug Administration Regulations CFR21 177.1520, paragraph (c), item 2.1 and, when used in accordance with FDA application guidelines, is suitable for food contact applications. Note: The product code followed by letters "-NAT" indicates natural, uncoloured product.

ALKATEQ™ XDS34P is a natural, unpigmented, additive free, low density polyethylene ground powder with a typical particle size of 95% <500 micron. ALKATEQ™ XDS34P conforms to the requirements of the United States Food and Drug Administration Regulations CFR21 177.1520, paragraph (c), item 2.1. and, when used in accordance with FDA application guidelines, is suitable for food contact applications. Typical applications include abrasive additive in industrial cleansers and non slip coatings. Note: The product code followed by letters "-NAT" indicates natural, uncoloured product.

Alkathene LD0128MS is a low density polyethylene designed for use in the production of medium gauge (40-80µm) high quality film. Alkathene LD0128MS is formulated with a process stabilisation and antiblock additive package and and an additive (erucamide) designed to confer a medium level of slip. Alkathene LD0128MS is particularly suitable for use in film applications where high clarity, medum to high strength and medium slip are required.

Alkathene LD0220MS is a low density polyethylene designed for use in the production of low gauge (20 - 50µm) high quality film. Alkathene LD0220MS is formulated with a process stabilisation and antiblock additive package and contains an additive (erucamide) designed to provide a medium level of slip. Film Extrusion: Alkathene LD0220MS is intended for use in high quality low gauge applications requiring medium slip, including lamination and overwrap films. It is typically blended with LLDPE for these applications.